SEAT – FRONT SEAT ASSEMBLY

SE–1

FRONT SEAT ASSEMBLY
SEAT
BODY

COMPONENTS

FRONT SEAT HEADREST ASSEMBLY

SEAT TRACK INNER
BRACKET COVER LH

SEAT TRACK OUTER COVER LH

37 (377, 27)

SE

FRONT SEAT ASSEMBLY

N*m (kgf*cm, ft.*lbf) : Specified torque

B132582E01

SE–2

SEAT – FRONT SEAT ASSEMBLY

FRONT SEAT CUSHION COVER

HOG RING

FRONT SEAT CUSHION PAD

42 (428, 31)

FRONT SEAT INNER BELT ASSEMBLY LH

SE

RECLINING ADJUSTER
RELEASE HANDLE LH

FRONT SEAT CUSHION
INNER SHIELD LH

FRONT SEAT CUSHION SHIELD LH
N*m (kgf*cm, ft.*lbf) : Specified torque
Non-reusable part
B132583E01

SE–3

SEAT – FRONT SEAT ASSEMBLY

FRONT SEATBACK PAD
FRONT SEAT HEADREST SUPPORT

FRONT SEATBACK COVER

HOG RING
FRONT SEAT ADJUSTER
FRAME ASSEMBLY
FRONT SEAT CUSHION
LOWER SHIELD LH
RECLINING ADJUSTER
LOWER INSIDE COVER RH
FRONT SEAT CUSHION
LOWER SHIELD RH

5.5 (56, 49 in.*lbf)

RECLINING ADJUSTER
UPPER INSIDE COVER RH

w/ Front Seat Side Airbag

SE

FRONT SEAT
ADJUSTER FRAME

OCCUPANT DETECTION ECU
(for Front Passenger Side)

RECLINING ADJUSTER
LOWER INSIDE COVER LH
8.0 (82, 71 in.*lbf)

SEAT POSITION AIRBAG SENSOR
(for Driver Side)

RECLINING ADJUSTER
UPPER INSIDE COVER LH

N*m (kgf*cm, ft.*lbf) : Specified torque
SEAT SLIDE POSITION PROTECTOR
Non-reusable part
B132584E01

SE–4

SEAT – FRONT SEAT ASSEMBLY

REMOVAL
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
1.

DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.

2.

REMOVE SEAT TRACK OUTER COVER LH
(a) Using a screwdriver, detach the 3 claws and remove
the seat track outer cover.
HINT:
Tape the screwdriver tip before use.

3.

REMOVE SEAT TRACK INNER BRACKET COVER LH
(a) Using a screwdriver, detach the 2 claws and remove
the seat track inner bracket cover.
HINT:
Tape the screwdriver tip before use.

4.

REMOVE FRONT SEAT HEADREST ASSEMBLY

5.

REMOVE FRONT SEAT ASSEMBLY
(a) Lift up the seat track adjusting handle and move the
seat to the rearmost position.
(b) Remove the 2 bolts on the front side of the seat.
(c) Lift up the seat track adjusting handle and move the
seat to the foremost position.
(d) Remove the 2 bolts on the rear side of the seat.
(e) Disconnect the connectors under the seat. Then
remove the front seat.
NOTICE:
Be careful not to damage the vehicle body.

B078868E02

B078867E02

SE

SEAT – FRONT SEAT ASSEMBLY

SE–5

DISASSEMBLY
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
CAUTION:
Wear protective gloves. Sharp surfaces on the seat
adjuster may injure your hands.
1.

REMOVE RECLINING ADJUSTER RELEASE
HANDLE LH
(a) Raise the reclining adjuster release handle to reveal
the claw.
(b) Using a screwdriver, detach the claw and remove
the release handle.
HINT:
Tape the screwdriver tip before use.

2.

REMOVE FRONT SEAT CUSHION SHIELD LH
(a) Remove the 2 rubber bands from the back of the
front seatback cover.

Claw

B079988E01

B132586

(b) Remove the 2 screws.
(c) Using a screwdriver, detach the 2 claws and clip,
and remove the seat cushion shield.
HINT:
Tape the screwdriver tip before use.
3.

REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
(See page SB-6)

SE
B132590

B076921E02

4.

REMOVE FRONT SEAT CUSHION INNER SHIELD LH
(a) Remove the screw.
(b) Using a screwdriver, detach the claw and clip, and
remove the seat cushion inner shield.
HINT:
Tape the screwdriver tip before use.

5.

REMOVE FRONT SEAT CUSHION COVER
(a) Detach the hooks and remove the 2 hog rings and
seat cushion cover (with pad) from the seat adjuster.

SE–6

SEAT – FRONT SEAT ASSEMBLY

(b) Remove the 6 hog rings and seat cushion cover
from the seat cushion pad.

Hog Ring

B132587E01

6.

REMOVE FRONT SEATBACK COVER
(a) Lift up the seatback cover and remove the 3 hog
rings shown in the illustration.

Hog Ring
B076023E01

(b) Remove the 3 hog rings shown in the illustration.
Rubber

Hog Ring
B077035E01

(c) Using a screwdriver, detach the 2 hooks.

SE
Hook
T

B132588E01

(d) w/ Front Seat Side Airbag:
Remove the nut and 2 seatback cover brackets.
(e) Roll up the seatback cover.

B087721E01

SEAT – FRONT SEAT ASSEMBLY

SE–7

(f)

Detach the 4 claws and remove the 2 headrest
supports.
(g) Remove the seatback cover (with pad) from the seat
adjuster.

B060977E01

(h) Remove the 4 hog rings and seatback cover from
the seatback pad.

Hog Ring
T

B132589E01

7.

REMOVE RECLINING ADJUSTER UPPER INSIDE
COVER LH
(a) Remove the screw and inside cover.

8.

REMOVE RECLINING ADJUSTER UPPER INSIDE
COVER RH
(a) Remove the screw and inside cover.

9.

REMOVE RECLINING ADJUSTER LOWER INSIDE
COVER LH
(a) Remove the screw and inside cover.

10. REMOVE RECLINING ADJUSTER LOWER INSIDE
COVER RH
(a) Remove the screw and inside cover.
11. REMOVE FRONT SEAT CUSHION LOWER SHIELD
LH
(a) Detach the claw and remove the lower shield.
12. REMOVE FRONT SEAT CUSHION LOWER SHIELD
RH
(a) Detach the claw and remove the lower shield.
13. REMOVE SEAT POSITION AIRBAG SENSOR (for
Driver Side) (See page RS-321)
14. REMOVE OCCUPANT DETECTION ECU (for Front
Passenger Side)

SE

SE–8

SEAT – FRONT SEAT ASSEMBLY

REASSEMBLY
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
CAUTION:
Wear protective gloves. Sharp surfaces on the seat
adjuster may injure your hands.

Hog Ring Pliers

SE

1.

INSTALL OCCUPANT DETECTION ECU (for Front
Passenger Side)

2.

INSTALL SEAT POSITION AIRBAG SENSOR (for
Driver Side) (See page RS-321)

3.

INSTALL FRONT SEAT CUSHION LOWER SHIELD LH
(a) Attach the claw to install the lower shield.

4.

INSTALL FRONT SEAT CUSHION LOWER SHIELD
RH
(a) Attach the claw to install the lower shield.

5.

INSTALL RECLINING ADJUSTER UPPER INSIDE
COVER LH
(a) Install the inside cover with the screw.

6.

INSTALL RECLINING ADJUSTER UPPER INSIDE
COVER RH
(a) Install the inside cover with the screw.

7.

INSTALL RECLINING ADJUSTER LOWER INSIDE
COVER LH
(a) Install the inside cover with the screw.

8.

INSTALL RECLINING ADJUSTER LOWER INSIDE
COVER RH
(a) Install the inside cover with the screw.

9.

INSTALL FRONT SEATBACK COVER
NOTICE:
• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the
cover.

B050126E09

(a) Using hog ring pliers, install the seatback cover to
the seatback pad with 4 new hog rings.
(b) Install the seatback cover (with pad) to the seat
adjuster.

Hog Ring
T

B132589E01

SEAT – FRONT SEAT ASSEMBLY

SE–9

(c) Attach the 4 claws to install the 2 headrest supports.

B060977E01

B087721E01

(d) w/ Front Seat Side Airbag:
Fully cover the airbag with the 2 seatback cover
brackets and install the nut.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
NOTICE:
• For vehicles with side airbags, the seatback
cover must be securely installed. If not, the
side airbag may not deploy properly.
• Make sure that the strap is not twisted after
installing the bracket.
• Install the bracket securely.
(e) Attach the 2 hooks to the seat adjuster.

Hook
B132588E01

T

(f)
Rubber

Using hog ring pliers, attach a rubber with 3 new
hog rings.

SE
Hog Ring
B077035E01

(g) Using hog ring pliers, install 3 new hog rings.

Hog Ring
B076023E01

SE–10

SEAT – FRONT SEAT ASSEMBLY

10. INSTALL FRONT SEAT CUSHION COVER
NOTICE:
• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the
cover.

Hog Ring Pliers

B050126E09

(a) Using hog ring pliers, install the seat cushion cover
to the seat cushion pad with 6 new hog rings.
(b) Using hog ring pliers, install the seat cushion cover
(with pad) to the seat adjuster with 2 new hog rings
and hooks.
11. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
(See page SB-6)
Hog Ring

B132587E01

12. REMOVE FRONT SEAT CUSHION INNER SHIELD LH
(a) Attach the claw and clip to install the seat cushion
inner shield.
(b) Install the screw.

B076921E02

13. INSTALL FRONT SEAT CUSHION SHIELD LH
(a) Attach the 2 claws and clip to install the seat
cushion shield.
(b) Install the screw.

SE
B132590E01

(c) Attach the 2 rubber bands of back of the front
seatback cover.
14. INSTALL RECLINING ADJUSTER RELEASE HANDLE
LH
(a) Attach the claw to install the release handle.

B132585

SEAT – FRONT SEAT ASSEMBLY

SE–11

INSTALLATION
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
1.

INSTALL FRONT SEAT ASSEMBLY
(a) Place the seat in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
(b) Connect the connectors under the seat.
(c) Install the 2 bolts on the front side of the seat.
Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf)
(d) Install the 2 bolts on the rear side of the seat.
Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf)

2.

INSPECT AND ADJUST SEAT SLIDE ADJUSTER
LOCKS
(a) During sliding operation of the front seat, check that
the left and right adjusters move together smoothly
and lock simultaneously. If the seat adjusters do not
lock simultaneously, loosen the seat fixation bolts to
adjust the adjuster's position.

3.

INSTALL SEAT TRACK OUTER COVER LH
(a) Attach the 3 claws to install the seat track outer
cover.

4.

INSTALL SEAT TRACK INNER BRACKET COVER LH
(a) Attach the 2 claws to install the seat track bracket
cover.

5.

CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL

B078868E02

6.

INSPECT FRONT SEAT ASSEMBLY (for Front
Passenger Side)
(a) Perform the zero point calibration and sensitivity
check (see page RS-174).

7.

PERFORM INITIALIZATION
(a) Perform initialization (see page IN-32).
NOTICE:
Certain systems need to be initialized after
disconnecting and reconnecting the cable from
the negative (-) battery terminal.

8.

CHECK SRS WARNING LIGHT
(a) Check the SRS warning light (see page RS-31).

B078867E02

SE

SE–12

SEAT – REAR SEAT ASSEMBLY

REAR SEAT ASSEMBLY
SEAT
BODY

COMPONENTS
REAR SEATBACK
ASSEMBLY RH

REAR SEATBACK HINGE
SUB-ASSEMBLY RH

REAR SEATBACK CENTER
HINGE SUB-ASSEMBLY
18.1(185, 13)

REAR SIDE SEATBACK
ASSEMBLY RH

18.1(185, 13)
42(428, 31)
36.8(375, 27)

36.8(375, 27)

REAR DOOR SCUFF PLATE RH
REAR SEATBACK ASSEMBLY LH
36.8(375, 27)
18.1(185, 13)

SE

REAR SEATBACK HINGE SUB-ASSEMBLY LH

REAR SIDE SEATBACK
ASSEMBLY LH

REAR SEAT CUSHION ASSEMBLY
REAR DOOR SCUFF PLATE LH
N*m (kgf*cm, ft.*lbf) : Specified torque

B132599E03

SE–13

SEAT – REAR SEAT ASSEMBLY

REAR SEATBACK LOCK RELEASE BUTTON
REAR SEATBACK STOP BUTTON GROMMET
REAR SEATBACK LOCK ASSEMBLY LH
REAR SEAT HEADREST ASSEMBLY LH

REAR SEAT HEADREST SUPPORT
18.1 (185, 13)

REAR SEATBACK FRAME LH
REAR SEAT SHOULDER BELT GUIDE CENTER
REAR SEATBACK PAD LH
REAR SEATBACK COVER LH

REAR SEATBACK COVER

x5

x2

CLIP

CLIP
HOG RING

SE

REAR SEAT CUSHION COVER

HOG RING

REAR SEAT CUSHION PAD
N*m (kgf*cm, ft.*lbf) : Specified torque
Non-reusable part
B132608E03

SE–14

SEAT – REAR SEAT ASSEMBLY

REAR SEAT OUTER BELT ASSEMBLY CENTER
REAR SEAT CENTER HEADREST ASSEMBLY
REAR SEAT SHOULDER BELT COVER
REAR SEAT HEADREST ASSEMBLY RH
REAR SEAT SHOULDER BELT
GUIDE CENTER
42 (428, 31)

REAR SEAT HEADREST
SUPPORT

REAR SEAT HEADREST
SUPPORT

REAR SEAT LOCK
RELEASE BUTTON
REAR SEATBACK STOP
BUTTON GROMMET

HOG RING
18.1 (185, 13)

REAR SEATBACK COVER

x5
REAR SEATBACK FRAME RH
x4

CLIP

REAR SEATBACK LOCK ASSEMBLY RH
CLIP

SE

REAR SEATBACK PAD RH

REAR SEATBACK COVER RH

CENTER ARMREST HINGE COVER

REAR SEAT CENTER ARMREST ASSEMBLY
N*m (kgf*cm, ft.*lbf) : Specified torque
Non-reusable part
B132674E03

SEAT – REAR SEAT ASSEMBLY

SE–15

REMOVAL

A

1.

REMOVE REAR SEAT CUSHION ASSEMBLY
(a) Detach the seat cushion's 2 front hooks from the
vehicle body.
NOTICE:
Follow the instructions below carefully as the
cushion frame deforms easily.
(1) Choose a hook to detach first. Place your
hands near the hook as shown in the
illustration. Then lift the seat cushion to detach
the hook.
(2) Repeat for the other hook.
(b) Detach the seat cushion's rear hook.
(c) Remove the seat cushion.

2.

REMOVE REAR SEATBACK ASSEMBLY LH
(a) Open the front part of the rear No. 1 floor deck
board.
(b) Tilt the seatback down toward the front of the
vehicle.

A: 100 mm (3.94 in.)
or Less
B132600E01

(c) Remove the 2 bolts and seatback.
3.

REMOVE REAR SEATBACK ASSEMBLY RH
(a) Remove the bolt and disconnect the rear seat outer
belt floor anchor.
(b) Open the front part of the rear No. 1 floor deck
board.
(c) Tilt the seatback down toward the front of the
vehicle.

B076029E01

(d) Remove the 2 bolts and seatback.

B076029E01

4.

REMOVE REAR DOOR SCUFF PLATE LH (See page
IR-9)

5.

REMOVE REAR DOOR SCUFF PLATE RH (See page
IR-9)

6.

REMOVE REAR SIDE SEATBACK ASSEMBLY LH
(a) Remove the bolt and side seatback.

7.

REMOVE REAR SIDE SEATBACK ASSEMBLY RH
(a) Remove the bolt and side seatback.

8.

REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY
LH
(a) Remove the bolt and hinge.

9.

REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY
RH
(a) Remove the bolt and hinge.

SE

SE–16

SEAT – REAR SEAT ASSEMBLY

10. REMOVE REAR SEATBACK CENTER HINGE SUBASSEMBLY
(a) Remove the 2 bolts and hinge.

B076041E01

SE

SEAT – REAR SEAT ASSEMBLY

SE–17

DISASSEMBLY
CAUTION:
Wear protective gloves. Sharp areas on the seatback
frame may injure your hands.
for Front Side

1.

REMOVE REAR SEAT CUSHION COVER
(a) Remove the 51 hog rings and cushion cover from
the cushion pad.

2.

REMOVE REAR SEAT HEADREST ASSEMBLY LH

3.

REMOVE REAR SEAT HEADREST ASSEMBLY RH

4.

REMOVE REAR SEAT CENTER HEADREST
ASSEMBLY

5.

REMOVE REAR SEAT CENTER ARMREST
ASSEMBLY
(a) Using a screwdriver, pry out the armrest hinge
cover.
HINT:
Tape the screwdriver tip before use.

6.

REMOVE REAR SEATBACK COVER LH
(a) Remove the rear seatback lock release button.
(b) Remove the 2 screws and shoulder belt guide.

for Back Side

Hog Ring
B132607E02

Claw

B078650E01

(c) Using a screwdriver, detach the claws and remove
the seatback stop button grommet.
HINT:
In order to detach the claws of the seatback stop
button grommet, insert your hand between the
seatback frame and the seatback cover (with pad).

Claw
B133833E01

SE

SE–18

SEAT – REAR SEAT ASSEMBLY

(d) Using a screwdriver, detach the 4 claws and remove
the rear seatback cover.
HINT:
Tape the screwdriver tip before use.

B078657E02

(e) Using a clip remover, remove the 7 clips.
NOTICE:
If clips are damaged during removal, replace
them.

B076036E01

(f)

Lift up the seatback cover and remove the 12 hog
rings.
(g) Detach the claws and remove the 2 headrest
supports.
(h) Remove the seatback cover (with pad) from the
seatback frame.

Hog Ring
B132603E01

(i)

Remove the 6 hog rings and seatback cover from
the seatback pad.

SE
Hog Ring
B132604E01

7.
B

A
Claw

B084817E02

REMOVE REAR SEAT BACK COVER RH
(a) Using a screwdriver, detach the 2 claws labeled A.
HINT:
Tape the screwdriver tip before use.
(b) Pull the shoulder belt cover in the direction indicated
by the arrow in the illustration to detach the 2 claws
labeled B. Then remove the shoulder belt cover.
(c) Remove the rear seatback lock release button.
(d) Remove the 2 screws and shoulder belt guide.

SEAT – REAR SEAT ASSEMBLY

SE–19

(e) Using a screwdriver, detach the claws and remove
the seatback stop button grommet.
HINT:
In order to detach the claws of the seatback stop
button grommet, insert your hand between the
seatback frame and the seatback cover (with pad).

Claw
B076952E01

(f)

Using a screwdriver, detach the 4 claws and remove
the rear seatback cover.
HINT:
Tape the screwdriver tip before use.

B078657E02

(g) Using a clip remover, remove the 9 clips.
NOTICE:
If clips are damaged during removal, replace
them.

B076033E01

(h) Lift up the seatback cover and remove the 14 hog
rings.
(i) Detach the claws and remove the 2 headrest
supports.
(j) Remove the seatback cover (with pad) from the
seatback frame.

Hog Ring
B132605E01

(k) Remove the 14 hog rings and seatback cover from
the seatback pad.
8.

Hog Ring
B132606E01

REMOVE REAR SEAT OUTER BELT ASSEMBLY
CENTER (See page SB-22)

SE

SE–20

SEAT – REAR SEAT ASSEMBLY

9.

REMOVE REAR SEATBACK LOCK ASSEMBLY LH
(a) Remove the 2 bolts and lock.

10. REMOVE REAR SEATBACK LOCK ASSEMBLY RH
(a) Remove the 2 bolts and lock.

B133834E01

SE

SEAT – REAR SEAT ASSEMBLY

SE–21

REASSEMBLY
CAUTION:
Wear protective gloves. Sharp areas on the seatback
frame may injure your hands.
1.

INSTALL REAR SEATBACK LOCK ASSEMBLY LH
(a) Install the lock with the 2 bolts.
Torque: 18.1 N*m (185 kgf*cm, 13 ft.*lbf)

2.

INSTALL REAR SEATBACK LOCK ASSEMBLY RH
(a) Install the lock with the 2 bolts.
Torque: 18.1 N*m (185 kgf*cm, 13 ft.*lbf)

3.

INSTALL REAR SEAT OUTER BELT ASSEMBLY
CENTER (See page SB-23)

4.

INSTALL REAR SEAT BACK COVER LH
NOTICE:
• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the
cover.
(a) Install the seatback cover (with pad) to the seatback
frame.
NOTICE:
Be careful not to damage the cover.

B133834E01

Hog Ring Pliers

B050126E09

(b) Using hog ring pliers, install the seatback cover to
the seatback pad with 6 new hog rings.
(c) Install the seatback cover (with pad) to the seatback
frame.
(d) Attach the claws to install the 2 headrest supports.

Hog Ring
B132604E01

(e) Using hog ring pliers, install 12 new hog rings.

Hog Ring
B132603E01

SE

SE–22

SEAT – REAR SEAT ASSEMBLY

(f)

Install the 7 clips.

B076036E01

(g) Attach the 4 claws to install the rear seatback cover.

Claws

B078657E03

(h) Attach the claws to install the seatback stop button
grommet.
(i) Install the shoulder belt guide with the 2 screws.
(j) Install the rear seatback lock release button.

Claw
B133833E01

5.
Hog Ring Pliers

SE

INSTALL REAR SEATBACK COVER RH
NOTICE:
• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the
cover.
(a) Install the seatback cover (with pad) to the seatback
frame.
NOTICE:
Be careful not to damage the cover.

B050126E09

(b) Using hog ring pliers, install the seatback cover to
the seatback pad with 14 new hog rings.
(c) Install the seatback cover (with pad) to the seatback
frame.
(d) Attach the claws to install the 2 headrest supports.

Hog Ring
B132606E01

SEAT – REAR SEAT ASSEMBLY

SE–23

(e) Using hog ring pliers, install 14 new hog rings.

Hog Ring
B132605E01

(f)

Install the 9 clips.

B076033E01

(g) Attach the 4 claws to install the rear seatback cover.

Claws

B078657E03

(h) Attach the claws to install the seatback stop button
grommet.
(i) Install the shoulder belt guide with the 2 screws.
(j) Install the rear seatback lock release button.

SE
Claw
B076952E01

(k) Attach the 4 claws to install the shoulder belt cover.
6.

INSTALL REAR SEAT CENTER ARMREST
ASSEMBLY
(a) Install the armrest with the bolt.
(b) Attach the claw to install the armrest hinge cover.

7.

INSTALL REAR SEAT HEADREST ASSEMBLY LH

8.

INSTALL REAR SEAT HEADREST ASSEMBLY RH

9.

INSTALL REAR SEAT CENTER HEADREST
ASSEMBLY

B

A
Claw

B084817E03

SE–24

SEAT – REAR SEAT ASSEMBLY

10. INSTALL REAR SEAT CUSHION COVER
(a) Using hog ring pliers, install the cushion cover to the
cushion pad with 51 new hog rings.
NOTICE:
• Be careful not to damage the cover.
• When installing the hog rings, minimize
wrinkles as much as possible.

for Front Side

for Back Side

Hog Ring
B076042E02

INSTALLATION
1.

INSTALL REAR SEATBACK CENTER HINGE SUBASSEMBLY
(a) Install the hinge with the 2 bolts.
Torque: 18.1 N*m (185 kgf*cm, 13 ft.*lbf)

2.

INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY
LH
(a) Install the hinge with the bolt.
Torque: 18.1 N*m (185 kgf*cm, 13 ft.*lbf)

3.

INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY
RH
(a) Install the hinge with the bolt.
Torque: 18.1 N*m (185 kgf*cm, 13 ft.*lbf)

4.

INSTALL REAR SIDE SEATBACK ASSEMBLY LH
(a) Install the side seatback with the bolt.

5.

INSTALL REAR SIDE SEATBACK ASSEMBLY RH
(a) Install the side seatback with the bolt.

6.

INSTALL REAR DOOR SCUFF PLATE LH (See page
IR-18)

7.

INSTALL REAR DOOR SCUFF PLATE RH (See page
IR-18)

B076041

SE

SEAT – REAR SEAT ASSEMBLY

SE–25

8.

INSTALL REAR SEATBACK ASSEMBLY LH
(a) Install the seatback with the 2 bolts.
Torque: 36.8 N*m (375 kgf*cm, 27 ft.*lbf)
(b) Close the front part of the rear No. 1 floor deck
board.
(c) Return the seatback to the upright position.

9.

INSTALL REAR SEATBACK ASSEMBLY RH
(a) Install the seatback with the 2 bolts.
Torque: 36.8 N*m (375 kgf*cm, 27 ft.*lbf)
(b) Close the front part of the rear No. 1 floor deck
board.
(c) Return the seatback to the upright position.
(d) Connect the rear seat outer belt floor anchor with
the bolt.
Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)

B076029E01

B076028E01

10. INSTALL REAR SEAT CUSHION ASSEMBLY
NOTICE:
When installing the seat cushion, make sure the seat
belt buckle is not under the seat cushion.
(a) Attach the seat cushion's rear hook to the center
hinge.
(b) Insert the inner belts through the slits on the seat
cushion.

SE
B132601E01

(c) Attach the seat cushion's 2 front hooks to the
vehicle body.
(d) Confirm that the seat cushion is firmly installed.

B132602