MI–1

MIRROR – POWER MIRROR CONTROL SYSTEM

POWER MIRROR CONTROL SYSTEM
MIRROR
BODY

PARTS LOCATION
DRIVER SIDE JUNCTION BLOCK
- ACC FUSE
- AM2 FUSE
- ACC-B FUSE
OUTER REAR
VIEW MIRROR RH

OUTER REAR
VIEW MIRROR
LH

MI

ACC RELAY

OUTER MIRROR SWITCH
Left/Right Adjustment
Switch

Outer Mirror Switch

B127647E01

MI–2

MIRROR – POWER MIRROR CONTROL SYSTEM

SYSTEM DIAGRAM
Outer Mirror Switch
B
from Multiplex Communication System

Left

Right

Up

Mirror
Switch

Down

Left/ Right/
Up
Down

Select
Switch
SSW1

AM1

SSW2

HL

HR

VL

VR

M+

MH MV

M+

E

ACCD
ACC

Power Source
Control ECU

ACC
AM2

MI

MH MV

ACC-B

M

M+

M

Outer Rear View
Mirror LH

from Battery

M

M

Outer Rear View
Mirror RH

from Battery

B127648E01

MI–3

MIRROR – POWER MIRROR CONTROL SYSTEM

PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of the
problem symptom. The potential causes of the symptoms are
listed in order of probability in the "Suspected area" column of
the table. Check each symptom by checking the suspected
areas in the order they are listed. Replace parts as
necessary.
Power mirror control system
Symptom

Mirror does not operate

Mirror operates abnormally

Suspected area

See page

1. ACC fuse

MI-1

2. AM2 fuse

MI-1

3. ACC-B fuse

MI-1

4. ACC relay

MI-1

5. Outer mirror switch assembly

MI-14

6. Outer rear view mirror assembly

MI-10

7. Wire harness

-

1. ACC fuse

MI-1

2. AM2 fuse

MI-1

3. ACC-B fuse

MI-1

4. ACC relay

MI-1

5. Outer mirror switch assembly

MI-14

6. Outer rear view mirror assembly

MI-10

7. Wire harness

-

MI

MI–4

MIRROR – INNER REAR VIEW MIRROR

INNER REAR VIEW MIRROR
MIRROR
BODY

COMPONENTS
w/ EC Mirror

INNER REAR VIEW
MIRROR COVER

INNER REAR VIEW MIRROR ASSEMBLY

MI
INNER REAR VIEW MIRROR ASSEMBLY

B129178E01

MIRROR – INNER REAR VIEW MIRROR

MI–5

REMOVAL
HINT:
EC mirror stands for "electrochromic mirror".
1.

REMOVE INNER REAR VIEW MIRROR ASSEMBLY
(w/o EC Mirror)
(a) Push the cover in the direction indicated by the
arrows labeled A and remove it.
(b) While holding down the claw in the direction
indicated by the black arrow labeled B, slide the
mirror in the direction indicated by the white arrow
and remove it.

2.

REMOVE INNER REAR VIEW MIRROR ASSEMBLY
(w/ EC Mirror)
(a) Remove the inner rear view mirror cover.
(b) Remove the screw.
(c) Slide the mirror in the direction indicated by the
arrow in the illustration and remove the mirror.

A
Cover
A

Claw

B

B064964E02

MI
B056435E02

MI–6

MIRROR – INNER REAR VIEW MIRROR

INSPECTION
1.
10

8

Battery

INSPECT INNER REAR VIEW MIRROR ASSEMBLY
(w/ EC Mirror)
(a) Check operation of the electrochromic inner mirror.
(1) Connect the battery's positive (+) lead to
terminal 10 and the negative (-) lead to terminal
8.
(2) Attach black colored tape to the forward sensor
to block it.
(3) Light up the mirror with an electric light, and
check that the mirror surface changes from
bright to dark.
If the result is not as specified, replace the
mirror assembly.

Sensor

Black Colored Tape

Bright

Dark
B137708E04

INSTALLATION

MI

1.

Cover

Claw

B113835E01

INSTALL INNER REAR VIEW MIRROR ASSEMBLY
(w/o EC Mirror)
(a) Install the mirror in the direction of the white arrow.
(b) Install the cover as shown in the illustration.

MIRROR – INNER REAR VIEW MIRROR

2.

MI–7

INSTALL INNER REAR VIEW MIRROR ASSEMBLY
(w/ EC Mirror)
(a) Install the mirror.
(b) Install the screw.
(c) Install the inner rear view mirror cover.

B056435E05

MI

MI–8

MIRROR – OUTER REAR VIEW MIRROR

OUTER REAR VIEW MIRROR
MIRROR
BODY

COMPONENTS
OUTER REAR VIEW MIRROR ASSEMBLY LH

MIRROR

MIRROR COVER

5.5 (56, 49 in.*lbf)

DOOR PULL HANDLE
FRONT DOOR TRIM BOARD
SUB-ASSEMBLY LH

MI

FRONT DOOR LOWER FRAME
BRACKET GARNISH LH
FRONT DOOR INSIDE
HANDLE BEZEL LH
for RH Side

FRONT DOOR ARMREST
UPPER BASE PANEL

FRONT DOOR ARMREST
UPPER BASE PANEL

N*m (kgf*cm, ft.*lbf) : Specified torque
B135938E01

MIRROR – OUTER REAR VIEW MIRROR

MI–9

REMOVAL
HINT:
• Use the same procedures for the LH side and RH side.
• The procedures listed below are for the LH side.
1.

DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.

2.

REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
(See page ED-11)

3.

REMOVE FRONT DOOR LOWER FRAME BRACKET
GARNISH LH (See page ED-11)

4.

REMOVE DOOR PULL HANDLE (See page ED-11)

5.

REMOVE FRONT DOOR ARMREST BASE PANEL
UPPER (See page ED-11)

6.

REMOVE FRONT DOOR TRIM BOARD SUBASSEMBLY LH (See page ED-12)

7.

REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
LH
(a) Disconnect the mirror connector.
(b) Remove the 3 nuts and mirror.

8.

REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
LH
(a) Using a moulding remover, detach the 4 claws and
outer rear view mirror.
HINT:
Apply protective tape to the mirror body.

B075148E01

Protective Tape
B137710E01

MI

MI–10

MIRROR – OUTER REAR VIEW MIRROR

(b) Disconnect the 2 connectors and remove the mirror.

B136005

(c) Using a screwdriver, detach the 6 claws and remove
the mirror cover.
HINT:
Tape the screwdriver tip before use.

B076118E01

INSPECTION
1.

(A)
(C)

(D)
(B)

MI

MH
M+

MV
B070997E04

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
LH
(a) Disconnect the mirror connector.
(b) Apply battery voltage and check the operation of the
mirror.
OK

Measurement Condition

Specified
Condition

Battery positive (+) → Terminal 5 (MV)
Battery negative (-) → Terminal 4 (M+)

Turns upward
(A)

Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 5 (MV)

Turns
downward (B)

Battery positive (+) → Terminal 3 (MH)
Battery negative (-) → Terminal 4 (M+)

Turns left (C)

Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 3 (MH)

Turns right (D)

If the result is not as specified, replace the mirror
assembly.

MI–11

MIRROR – OUTER REAR VIEW MIRROR

(c) Apply battery voltage to the mirror terminals and
check the operation of the mirror heater.
OK
Measurement Condition

Specified
Condition

Battery positive (+) → Terminal 2 (M+)
Battery negative (-) → Terminal 1 (M-)

Mirror becomes
warm

If the result is not as specified, replace the mirror
assembly.

MM+

B076304E01

2.
(A)
(C)

(D)
(B)

MH
M+

MV
B070998E03

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
RH
(a) Disconnect the mirror connector.
(b) Apply battery voltage and check the operation of the
mirror.
OK

Measurement Condition

Specified
Condition

Battery positive (+) → Terminal 5 (MV)
Battery negative (-) → Terminal 4 (M+)

Turns upward
(A)

Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 5 (MV)

Turns downward
(B)

Battery positive (+) → Terminal 3 (MH)
Battery negative (-) → Terminal 4 (M+)

Turns left (C)

Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 3 (MH)

Turns right (D)

If the result is not as specified, replace the mirror
assembly.
(c) Apply battery voltage to the mirror terminals and
check the operation of the mirror heater.
OK
Measurement Condition

Specified
Condition

Battery positive (+) → Terminal 2 (M+)
Battery negative (-) → Terminal 1 (M-)

Mirror becomes
warm

If the result is not as specified, replace the mirror
assembly.

MM+

B076303E01

MI

MI–12

MIRROR – OUTER REAR VIEW MIRROR

INSTALLATION
1.

INSTALL OUTER MIRROR COVER LH
(a) Install the mirror cover as shown in the illustration.

B075311E01

(b) Check that there is no gap between the cover and
mirror body.
HINT:
If there is a gap between the cover and body, noise
will occur during driving.

Mirror Body

Mirror Cover
B076333E01

(c) Connect the 2 connectors.

MI
B136005

(d) Attach the 4 claws to install the mirror.

B075313E01

MIRROR – OUTER REAR VIEW MIRROR

MI–13

2.

INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
LH
(a) Install the mirror with the 3 nuts.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
(b) Connect the connector.

3.

INSTALL FRONT DOOR TRIM BOARD SUBASSEMBLY LH (See page ED-21)

4.

INSTALL FRONT DOOR ARMREST BASE PANEL
UPPER LH (See page ED-21)

5.

INSTALL DOOR PULL HANDLE (See page ED-22)

6.

INSTALL FRONT DOOR LOWER FRAME BRACKET
GARNISH LH (See page ED-22)

7.

INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
(See page ED-22)

8.

PERFORM INITIALIZATION
(a) Perform initialization (see page SS-2).
NOTICE:
Certain systems need to be initialized after
disconnecting and reconnecting the cable from
the negative (-) battery terminal.

B075148E01

MI

MI–14

MIRROR – OUTER MIRROR SWITCH

OUTER MIRROR SWITCH
LEFT

RIGHT

INSPECTION

Left/Right Adjustment Switch

1.

Mirror
Switch
UP
LEFT
DOWN

No Pin

B

RIGHT

MRV

E

M+

MLH

MLV

No Pin

MRH
B059702E03

INSPECT OUTER MIRROR SWITCH ASSEMBLY
(a) The L position of the left/right adjustment switch:
Measure the resistance of the mirror switch.
Standard resistance (for left side)

Tester Connection

Switch Condition

Specified Condition

4 (MLV) - 8 (B)
6 (M+) - 7 (E)

UP

Below 1 Ω

4 (MLV) - 7 (E)
6 (M+) - 8 (B)

DOWN

Below 1 Ω

5 (MLH) - 8 (B)
6 (M+) - 7 (E)

LEFT

Below 1 Ω

5 (MLH) - 7 (E)
6 (M+) - 8 (B)

RIGHT

Below 1 Ω

If the result is not as specified, replace the switch
assembly.
(b) The R position of the left/right adjustment switch:
Measure the resistance of the mirror switch.
Standard resistance (for right side)
Tester Connection

Switch Condition

Specified Condition

3 (MRV) - 8 (B)
6 (M+) - 7 (E)

UP

Below 1 Ω

3 (MRV) - 7 (E)
6 (M+) - 8 (B)

DOWN

Below 1 Ω

2 (MRH) - 8 (B)
6 (M+) - 7 (E)

LEFT

Below 1 Ω

2 (MRH) - 7 (E)
6 (M+) - 8 (B)

RIGHT

Below 1 Ω

If the result is not as specified, replace the switch
assembly.

MI

MI–15

MIRROR – MIRROR HEATER RELAY

MIRROR HEATER RELAY
ON-VEHICLE INSPECTION
1.

1
3

5

2

1

INSPECT MIRROR HEATER RELAY
(a) Remove the mirror heater relay.
(b) Measure the resistance of the relay.
Standard resistance

2

Tester Connection

Specified Condition

3-5

10 kΩ or higher

5

Below 1 Ω
(when battery voltage is applied to
terminals 1 and 2)

3

If the result is not as specified, replace the relay.
(c) Install the mirror heater relay.

B060778E04

MI