BODY DIMENSIONS
Three-dimensional
distance

Center-to-center
straight-line
distance

DI-1

GENERAL INFORMATION
1.

BASIC DIMENSIONS

(a) There are two types of dimensions in the diagram.
(1) (Three-dimensional distance)


Straight-line distance between the centers of two
measuring points.

Two-dimensional
distance

Vertical distance
in center

Center-to-center
Horizontal distance
in forward / rearward

Vertical distance
in lower surface

Imaginary Standard Line

Under Surface of
The Rocker Panel

(2) (Two-dimensional distance)


Horizontal distance in forward/rearward between the
centers of two measuring points.


The height from an imaginary standard line.
(b) In cases in which only one dimension is given, left and right
are symmetrical.
(c) The dimensions in the following drawing indicate actual distance. Therefore, please use the dimensions as a reference.
(d) The line that connects the places listed below is the imaginary standard line when measuring the height. (The dimensions are printed in the text.)
SYMBOL

Name

1

The place that was lowered A mm from the under surface of
the rocker panel centered on the front jack up point.

2

The place that was lowered B mm from the under surface of
the rocker panel centered between 1 and 3.

3

The place that was lowered C mm from the under surface of
the rocker panel centered on the rear jack up point.

Imaginary Standard Line

BODY DIMENSIONS

DI-2
Plate Looseness
Body Looseness

Pointer Looseness

2.

MEASURING

(a) Basically, all measurements are to be done with a tracking
gauge. For portions where it is not possible to use a tracking gauge, a tape measure should be used.
(b) Use only a tracking gauge that has no looseness in the
body, measuring plate, or pointers.

Pointer
Master Gauge

Wrong

Correct

Pointer

HINT:
1) The height of the left and right pointers must be equal.
2) Always calibrate the tracking gauge before measuring
or after adjusting the pointer height.
3) Take care not to drop the tracking gauge or otherwise
shock it.
4) Confirm that the pointers are securely in the holes.
(c) When using a tape measure, avoid twists and bends in the
tape.

BODY DIMENSIONS

DI-3

BODY DIMENSION DRAWINGS
ENGINE COMPARTMENT
(Three-Dimensional Distance)

1,407
(55.39)
418
(16.46)

1,444
(56.85)
1,378
(54.25)

1,220
(48.03)

221
(8.70)
602
(23.70)

752
(29.61)

1,038
(40.87)

1,357
(53.43)

784
(30.87)

564
(22.20)

1,010
(39.76)
726
(28.58)

754
(29.69)
253
(9.96)

836
514
(20.24) (32.91)

563
(22.17)

769
(30.28)

818
(32.20)

848
(33.39)
830
(32.68)

525
(20.67)

997
(39.25)

263
(10.35)

440
(17.32)

559
(22.01)

Height from Imaginary Standard Line
A, a

C, c

M, m

692
(27.24)

825
(32.48)

623
(24.53)

Vehicle Dimensions
B-b

B-D
or
b-D

C-m
or
c-M

D-E

D-e

K-k

N-n

N-O
or
n-o

N-o
or
n-O

1,023
(40.28)

513
(20.20)

1,294
(50.94)

826
(32.52)

810
(31.89)

1,437
(56.57)

1,409
(55.47)

232
(9.13)

1,413
(55.63)

HINT: For symbols, capital letters indicate right side of vehicle,
small letters indicate left side of vehicle (Seen from rear).
Symbol

Name

mm (in.)

Hole dia.

Symbol

Name

Hole dia.

A, a

Radiator upper support standard hole

10 (0.39)

H, h

Radiator support standard hole

15 (0.59)

B, b

Front spring support hole-inner

11 (0.43)

I

Hood lock support installation nut

6 (0.24) nut

C, c

8 (0.31) bolt

Hood hinge installation nut

8 (0.31) nut

J, j

Front bumper reinforcement installation bolt

D

Cowl top outer panel installation nut

6 (0.24) nut

K, k

Front fender extension standard hole

E, e

Front side member standard hole

18 (0.71)

L, l

Radiator upper center support installation nut

6 (0.24) nut

F

Front side member standard hole

12 (0.47)

M, m

Radiator upper center support installation nut

6 (0.24) nut

f

Engine mounting installation nut

10 (0.39) nut

N, n

Front fender installation nut

6 (0.24) nut

G, g

Radiator support standard hole

10 (0.39)

O, o

Front fender installation nut

6 (0.24) nut

7 (0.28)

BODY DIMENSIONS

DI-4

BODY OPENING AREAS (Side View: Front)

(Three-Dimensional Distance)

1,148
(45.20)
971
(38.23)
1,599
(62.95)

662
(26.06)
1,151
(45.31)

830
(32.68)
929
(36.57)

1,407
(55.39)

1,073
(42.24)

1,041
(40.98)

830
(32.68)
1,026
(40.39)

Vehicle Dimensions Left 
 Right
E-e

F-f

G-g

H-h

I-i

J-j

K-k

1,282
(50.47)

1,430
(56.30)

1,434
(56.46)

1,435
(56.50)

1,171
(46.10)

1,331
(52.40)

1,431
(56.34)

E-f
or
e-F

E-h
or
e-H

E-j
or
e-J

F-j
or
f-J

F-k
or
f-K

H-i
or
h-I

J-k
or
j-K

1,544
(60.79)

1,644
(64.72)

1,464
(57.64)

1,797
(70.75)

1,654
(65.12)

1,663
(65.47)

1,509
(59.41)

HINT: For symbols, capital letters indicate right side of vehicle,
small letters indicate left side of vehicle (Seen from rear).
Symbol

Name

A, a

Roof panel corner

mm (in.)

Hole dia.

Symbol

—

H, h

Rocker panel assembly mark

Name

Hole dia.
—

B, b

Hood hinge installation nut-rear

8 (0.31) nut

I, i

Roof side rail assembly mark

—

C, c

Front door hinge installation nut

8 (0.31) nut

J, j

Center body pillar assembly mark

—

D, d

Front door hinge installation nut

8 (0.31) nut

K, k

Center body pillar assembly mark

—

E, e

Front body pillar assembly mark

—

L, l

Rear door hinge installation nut

8 (0.31) nut

F, f

Front body pillar assembly mark

—

M, m

Rear door hinge installation nut

8 (0.31) nut

G, g

Rocker panel assembly mark

—

—

—

—

BODY DIMENSIONS

DI-5

BODY OPENING AREAS (Side View: Rear)

(Three-Dimensional Distance)

1,052
(41.42)
809
(31.85)
910 1,031
(35.83) (40.59)
1,026
(40.39)

710
(27.95)

Vehicle Dimensions Left 
 Right
N-n

O-o

P-p

Q-q

R-r

S-s

1,337
(52.64)

1,426
(56.14)

1,434
(56.46)

1,147
(45.16)

1,295
(50.98)

1,427
(56.18)

G-p
or
g-P

I-q
or
i-Q

N-r
or
n-R

N-s
or
n-S

O-s
or
o-S

P-q
or
p-Q

R-s
or
r-S

1,756
(69.13)

1,390
(54.72)

1,544
(60.79)

1,654
(65.12)

1,593
(62.72)

1,659
(65.31)

1,492
(58.74)

HINT: For symbols, capital letters indicate right side of vehicle,
small letters indicate left side of vehicle (Seen from rear).
Symbol

Name

Hole dia.

mm (in.)

Symbol

Name

Hole dia.

G, g

Rocker panel assembly mark

—

P, p

Rocker panel assembly mark

—

I, i

Roof side rail assembly mark

—

Q, q

Roof side rail assembly mark

—

N, n

Center body pillar assembly mark

—

R, r

Quarter panel assembly mark

—

O, o

Center body pillar assembly mark

—

S, s

Quarter panel assembly mark

—

BODY DIMENSIONS

DI-6

BODY OPENING AREAS (Rear View)

(Three-Dimensional Distance)

1,095
(43.11)

1,110
(43.70)
1,216
(47.87)
1,255
(49.41)

488
(19.21)
1,117
(43.98)

1,201
(47.28)

1,418
(55.83)
1,252
(49.29)

1,095
(43.11)

1,062
(41.81)

1,067
(42.01)

Vehicle Dimensions
E-G

e-g

F-G

F-g

775
(30.51)

776
(30.55)

873
(34.37)

929
(36.57)

f-G

f-g

G-g

G-h
or
g-H

926
(36.46)

882
(34.72)

898
(35.35)

1,626
(64.02)

HINT: For symbols, capital letters indicate right side of vehicle,
small letters indicate left side of vehicle (Seen from rear).
Symbol

Name

mm (in.)

Hole dia.

Symbol

Name

Hole dia.

A, a

Back door hinge installation hole-outer

15 (0.59)

F, f

Body lower back panel reinforcement working hole

8 (0.31)

B, b

Back door damper stay installation nut

6 (0.24) nut

G, g

Back door lock striker installation nut

6 (0.24) nut

C, c

Back door cushion installation nut

6 (0.24) nut

H, h

Rear absorber mounting bracket standard hole

13 (0.51)

D, d

Quarter panel standard hole

13 (0.51)

I, i

Center body pillar assembly mark

E, e

Deck trim side board installation hole

8.5 (0.335)

—

—

—
—

BODY DIMENSIONS

DI-7

UNDER BODY

(Three-Dimensional Distance)
840
(33.07)

531
(20.91)
997
(39.25)

RH

317
(12.48)

985
(38.78)

400
(15.75)

890

(35.04)
1,080
(42.52) 1,093
1,263
(49.72)
(43.03)
912
683
(35.91)
(26.89)
530
(20.87)

1,228
(48.35)

870
(34.25)

966
(38.03)

1,170
(46.06)

1,223
(48.15)

1,135
(44.69)

1,031
(40.59)

522
(20.55)

849
(33.43)

1,023
(40.28) 1,008
(39.69)

956
(37.64)

968
(38.11)

879
(34.61)

641
(25.24)

1,126
(44.33)

952
874
(37.48)
(34.41)

498
(19.61)
248
(9.76)

Vehicle Dimensions

Front

227
86 59
(8.94) (3.39) (2.32)

260
(10.24)

657
(25.87)
1,492
(58.74)

839
(33.03)

396
385
188 316
(15.59) (15.16) (7.40) (12.44)

754
(29.69)

548
(21.57)

860
(33.86)

1,100
(43.31) 870
(34.25)

1,252
(49.29)

912
(35.91)

LH

E

1

2

3

I-l
or
i-L

103
(4.06)

100
(3.94)

105
(4.13)

1,282
(50.47)

53
(2.09)

37
(1.46)

141 119
(5.55) (4.69)

302
293
(11.89) (11.54)

293
(11.54)

Imaginary
Standard
Line

mm (in.)
Symbol

Name

Hole dia.

Symbol

Name

Hole dia.

A, a

Front bumper reinforcement installation bolt

8 (0.31) bolt

H, h

Center member floor No.5 reinforcement standard hole

10 (0.39)

B, b

Radiator lower support standard hole

10 (0.39)

I, i

Rear floor side member standard hole

25 (0.98)

C, c

Front side member standard hole

18 (0.71)

J, j

Trailing arm installation hole inner

13 (0.51)

D, d

Front suspension crossmember installation nut

14 (0.55) nut

K, k

Rear floor No.2 crossmember standard hole

10 (0.39)

E, e

Front suspension crossmember installation nut

14 (0.55) nut

L, l

Rear floor side member standard hole

16 (0.63)

F, f

Torque box front standard hole

25 (0.98)

M, m

Rear floor side member standard hole

18 (0.71)

G, g

Front side member standard hole

18 (0.71)

—

—

—

BODY DIMENSIONS

DI-8

UNDER BODY

(Three-Dimensional Distance)
2,064
(81.26)
2,332 2,174
(91.81) (85.59)

498
(19.61)

500
(19.69)

RH

1,020
(40.16)
1,539
(60.59)

1,120
(44.09)

626
(24.65)

550
(21.65)

0

435
(17.13)

200
(7.87)

LH

499
(19.65)

2,331
(91.77)

507
(19.96)

944
(37.17)

614
(24.17)

537
(21.14)

456
(17.95)

445
(17.52)

435
(17.13)

435
(17.13)

512
(20.16)

2,064
(81.26)

1,542
(60.71)

1,258
(49.53)

860
(33.86)

0

699
(27.52)

Wheel base

2,700 (106.3)

A
a
B, b C, c
E, e D, d
F, f G, g
396
385
188
316
731 227
86
59
(15.59) (15.16) (7.40) (12.44) (28.78) (8.94) (3.39) (2.32)

1

2

3

103
(4.06)

100
(3.94)

105
(4.13)

H, h
53
(2.09)

484
(19.06)

238
(9.37)

485
(19.09)

Front

1,480
(58.27)

I, i
37
(1.46)

265
(10.43)

437
(17.20)

484
(19.06)

1,020 1,225
(40.16) (48.23)

1,468
(57.80)

J, j
K, k
L, l M, m
N, n
141
119
399
302
293
(5.55) (4.69) (15.71) (11.89) (11.54)

O, o
293
(11.54)

Imaginary
Standard
Line
mm (in.)
Symbol

Name

Hole dia.

Symbol

Name

A, a

Front bumper reinforcement installation bolt

8 (0.31) bolt

I, i

Center member floor No.5 reinforcement standard hole

10 (0.39)

B, b

Radiator lower support standard hole

10 (0.39)

J, j

Rear floor side member standard hole

25 (0.98)

C, c

Front side member standard hole

18 (0.71)

K, k

Trailing arm installation hole inner

13 (0.51)

D, d

Front suspension crossmember installation nut

14 (0.55)nut

L, l

Rear spring bracket installation hole-front

12 (0.47)

E, e

Front spring support hole-outer

11 (0.43)

M, m

Rear floor No.2 crossmember standard hole

10 (0.39)

F, f

Front suspension crossmember installation nut

14 (0.55)nut

N, n

Rear floor side member standard hole

16 (0.63)

G, g

Torque box front standard hole

25 (0.98)

O, o

Rear floor side member standard hole

18 (0.71)

H, h

Front side member standard hole

18 (0.71)

—

—

Hole dia.

—

BODY DIMENSIONS

DI-9

REFERENCE VALUE
ENGINE COMPARTMENT
(Three-Dimensional Distance)

1,407
(55.39)

1,403
(55.24)
1,197
(47.13)

526
(20.71)
616
(24.25)
708
(27.87)

1,218
754 (47.95)
(29.69)
736
(28.98)

1,173
(46.18)

1,157
(45.55)

Vehicle Dimensions
A-B
or
a-b

A-E
or
a-e

C-c

96
(3.78)

698
(27.48)

1,449
(57.05)

HINT: These values are actual measurements made on this model.
Use these reference values.
Symbol

Name

mm (in.)

Hole dia.

Symbol

A, a

Front bumper installation screw

—

D, d

Headlight installation screw

Name

—

B, b

Radiator upper support installation bolt

—

E, e

Front fender installation bolt

—

C, c

Front end of front fender

—

—

—

Hole dia.

—

BODY DIMENSIONS

DI-10

UNDER BODY

(Two-Dimensional Distance)

Front bumper reinforcement

56.8

16.8

8.2

Front spring support

65.9 33.1

Rear spring support

71.2

2.3

11.8

10.9
5.7


57.1

33.3

2.3

63.8

57.1

2.3

32.8

0.4

3.4

0.6

1.8

2.3 0.6

1.6
2.8

85.2

mm