INTERIOR – FRONT FLOOR FOOTREST IR–1 FRONT FLOOR FOOTREST INTERIOR BODY COMPONENTS CLIP FRONT FLOOR FOOTREST B132598E02 REMOVAL 1. REMOVE FRONT FLOOR FOOTREST (a) Using a screwdriver, detach the 2 clips and remove the footrest. IR B074185E02 IR–2 INTERIOR – FRONT FLOOR FOOTREST INSTALLATION 1. B074185E02 IR INSTALL FRONT FLOOR FOOTREST (a) Attach the 2 clips to install the footrest. IR–3 INTERIOR – ROOF HEADLINING ROOF HEADLINING INTERIOR BODY COMPONENTS TONNEAU COVER ASSEMBLY BACK DOOR WEATHERSTRIP REAR NO. 3 FLOOR BOARD REAR NO. 2 FLOOR BOARD ROPE HOOK REAR DECK TRIM COVER ROPE HOOK REAR NO. 4 FLOOR BOARD REAR NO. 1 FLOOR BOARD REAR SIDE SEATBACK FRAME RH DECK FLOOR BOX LH REAR DECK FLOOR BOX IR REAR SIDE SEATBACK FRAME LH REAR SEAT CUSHION ASSEMBLY B132617E02 IR–4 INTERIOR – ROOF HEADLINING FRONT DOOR OPENING TRIM WEATHERSTRIP LH CENTER PILLAR GARNISH LH ROOF SIDE INNER GARNISH ASSEMBLY LH FRONT PILLAR GARNISH LH REAR DOOR OPENING TRIM WEATHERSTRIP LH FRONT PILLAR GARNISH CORNER PIECE LH 42 (430, 31) COWL SIDE TRIM BOARD LH 42 (430, 31) FRONT DOOR SCUFF PLATE LH IR LAP BELT OUTER ANCHOR COVER FRONT SEAT OUTER BELT ASSEMBLY LH REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH DECK TRIM SIDE PANEL ASSEMBLY LH REAR DOOR SCUFF PLATE LH CENTER PILLAR LOWER GARNISH LH N*m (kgf*cm, ft.*lbf) : Specified torque B132592E03 IR–5 INTERIOR – ROOF HEADLINING CENTER PILLAR GARNISH RH REAR DOOR OPENING TRIM WEATHERSTRIP RH FRONT DOOR OPENING TRIM WEATHERSTRIP RH DECK TRIM SIDE PANEL ASSEMBLY RH FRONT PILLAR GARNISH CORNER PIECE RH ROOF SIDE INNER GARNISH ASSEMBLY RH FRONT PILLAR GARNISH RH 42 (430, 31) 42 (430, 31) REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH COWL SIDE TRIM BOARD RH FRONT DOOR SCUFF PLATE RH CENTER PILLAR LOWER GARNISH RH REAR DOOR SCUFF PLATE RH LAP BELT OUTER ANCHOR COVER IR FRONT SEAT OUTER BELT ASSEMBLY RH N*m (kgf*cm, ft.*lbf) : Specified torque B132591E02 IR–6 INTERIOR – ROOF HEADLINING NO. 3 ROOF SILENCER PAD ROOF HEADLINING PAD NO. 2 ROOF SILENCER PAD ASSIST GRIP SUB-ASSEMBLY ROOF HEADLINING ASSEMBLY ASSIST GRIP COVER ASSIST GRIP COVER CLIP NO. 1 ROOM LIGHT ASSEMBLY MAP LIGHT ASSEMBLY VISOR HOLDER IR NO. 1 ROOM LIGHT LENS ASSIST GRIP COVER VISOR ASSEMBLY RH VISOR ASSEMBLY LH ASSIST GRIP COVER ASSIST GRIP SUB-ASSEMBLY B132597E02 IR–7 INTERIOR – ROOF HEADLINING REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE FRONT DOOR SCUFF PLATE LH (a) Using a screwdriver, detach the 8 claws and 2 clips, and remove the scuff plate. HINT: Tape the screwdriver tip before use. 3. REMOVE FRONT DOOR SCUFF PLATE RH HINT: Use the same procedures described for the LH side. 4. REMOVE COWL SIDE TRIM BOARD LH (a) Using a screwdriver, detach the claw and 2 clips, and remove the trim board. HINT: Tape the screwdriver tip before use. 5. REMOVE COWL SIDE TRIM BOARD RH HINT: Use the same procedures described for the LH side. 6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 8. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH (a) Put protective tape as shown in the illustration. Standard measurement B073586E02 B073588E02 B C A A Protective Tape Protective Tape B132622E01 Area Specified Condition A 2.0 mm (0.079 in.) B 10.0 mm (0.394 in.) C 50.0 mm (1.969 in.) (b) Using a screwdriver, detach the 5 claws and remove the corner piece. HINT: Tape the screwdriver tip before use. 9. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH HINT: Use the same procedures described for the LH side. IR IR–8 INTERIOR – ROOF HEADLINING 10. REMOVE FRONT PILLAR GARNISH LH (a) w/o Curtain Shield Airbag: Using a screwdriver, detach the 2 clips and remove the pillar garnish. HINT: Tape the screwdriver tip before use. B073594E03 (b) w/ Curtain Shield Airbag: Remove the pillar garnish. (1) Pull the pillar garnish so that clip B detaches, the base of clip A detaches, and the tip of clip A locks in the pillar garnish's hole. (2) Using needle-nose pliers, rotate clip A 90°. Then pull the pillar garnish to release the tip of clip A from the pillar garnish. (3) Pull the pillar garnish in the direction indicated by the arrow in the illustration to detach the claw. Pillar Garnish Clip A Pull 90° Claw Clip A Clip B B079223E02 120 mm (4.72 in.) 700 mm (27.56 in.) Double-sided Tape IR (c) w/ Curtain Shield Airbag: Protect the curtain shield airbag LH. (1) Thoroughly cover the airbag with cloth or nylon that is approximately 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with double-sided tape, as shown in the illustration. NOTICE: Cover the curtain shield airbag with the protective cover as soon as the pillar garnish is removed. 11. REMOVE FRONT PILLAR GARNISH RH HINT: Use the same procedures described for the LH side. 12. REMOVE REAR SEAT CUSHION ASSEMBLY (See page SE-15) Protective Cover B076392E04 INTERIOR – ROOF HEADLINING IR–9 13. REMOVE REAR DOOR SCUFF PLATE LH (a) Using a screwdriver, detach the 6 claws and clip, and remove the scuff plate. HINT: Tape the screwdriver tip before use. 14. REMOVE REAR DOOR SCUFF PLATE RH HINT: Use the same procedures described for the LH side. B073587E02 15. REMOVE REAR SIDE SEATBACK FRAME LH (a) Remove the bolt. (b) Detach the claw and remove the frame. 16. REMOVE REAR SIDE SEATBACK FRAME RH HINT: Use the same procedures described for the LH side. 17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH B076393E02 18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 19. REMOVE LAP BELT OUTER ANCHOR COVER (a) Using a screwdriver, detach the 3 claws and remove the anchor cover. HINT: Tape the screwdriver tip before use. 20. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (a) Remove the bolt and disconnect the floor anchor. B076394E03 21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (a) Remove the bolt and disconnect the floor anchor. 22. REMOVE CENTER PILLAR LOWER GARNISH LH (a) Using a screwdriver, detach the 2 claws and 2 clips, and remove the lower garnish. HINT: Tape the screwdriver tip before use. 23. REMOVE CENTER PILLAR LOWER GARNISH RH HINT: Use the same procedures described for the LH side. B073589E03 IR IR–10 INTERIOR – ROOF HEADLINING 24. REMOVE CENTER PILLAR GARNISH LH (a) Remove the 2 screws. (b) Using a screwdriver, detach the clip and remove the pillar garnish. HINT: Tape the screwdriver tip before use. 25. REMOVE CENTER PILLAR GARNISH RH HINT: Use the same procedures described for the LH side. B073590E02 26. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH (a) Remove the bolt and disconnect the floor anchor. 27. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH (a) Remove the bolt and disconnect the floor anchor. 28. REMOVE BACK DOOR WEATHERSTRIP 29. REMOVE TONNEAU COVER ASSEMBLY 30. REMOVE REAR NO. 2 FLOOR BOARD 31. REMOVE REAR NO. 3 FLOOR BOARD 32. REMOVE REAR NO. 4 FLOOR BOARD 33. REMOVE REAR DECK FLOOR BOX 34. REMOVE DECK FLOOR BOX LH Rope Hook Clip Clip 35. REMOVE REAR NO. 1 FLOOR BOARD (a) Remove the 2 bolts and the 2 rope hooks. (b) Using a clip remover, remove the 2 clips. (c) Using a screwdriver, detach the 5 clips and remove the floor board. HINT: Tape the screwdriver tip before use. B132619E01 IR 36. REMOVE REAR DECK TRIM COVER (a) Using a screwdriver, detach the 4 claws and remove the trim cover. HINT: Tape the screwdriver tip before use. B076395E02 INTERIOR – ROOF HEADLINING IR–11 37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (a) Remove the screw and 2 bolts. (b) Using a clip remover, remove the clip. (c) Using a screwdriver, detach the 7 claws and 3 clips, and remove the side panel. HINT: Tape the screwdriver tip before use. Clip B073591E02 38. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (a) Remove the screw and 2 bolts. (b) Using a clip remover, remove the clip. (c) Using a screwdriver, detach the 6 claws and 2 clips, and remove the side panel. HINT: Tape the screwdriver tip before use. Clip B079224E02 39. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (a) Using a screwdriver, detach the 6 clips and claw, and remove the inner garnish. HINT: Tape the screwdriver tip before use. B073592E03 40. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH HINT: Use the same procedures described for the LH side. IR IR–12 INTERIOR – ROOF HEADLINING 41. REMOVE MAP LIGHT ASSEMBLY (a) Remove the 2 screws. (b) Using a moulding remover, detach the 4 clips and remove the map light. (c) Disconnect the map light connector. B076771E02 42. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (a) Using a screwdriver, detach the 4 claws and remove the room light lens. HINT: Tape the screwdriver tip before use. Protective Tape Claw Claw Claw Claw B076772E03 (b) Using a screwdriver, detach the 4 claws and remove the room light. HINT: Tape the screwdriver tip before use. (c) Disconnect the room light connector. B073597E02 43. REMOVE ASSIST GRIP COVER (a) Using a screwdriver, detach the 4 claws and remove the 2 covers. HINT: Tape the screwdriver tip before use. IR B076398E04 INTERIOR – ROOF HEADLINING IR–13 44. REMOVE ASSIST GRIP SUB-ASSEMBLY (a) Using a screwdriver, detach the 4 claws and remove the assist grip. HINT: Tape the screwdriver tip before use. B076399E02 45. REMOVE VISOR ASSEMBLY LH (a) Remove the 2 screws. (b) Disconnect the connector and remove the visor. 46. REMOVE VISOR ASSEMBLY RH HINT: Use the same procedures described for the LH side. B075287E01 47. REMOVE VISOR HOLDER (a) Remove the visor holder by turning it counterclockwise. 90q B050596E01 48. REMOVE ROOF HEADLINING ASSEMBLY (a) Remove the 3 clips and headlining. (b) Remove the silencer pads and headlining pad from the headlining. (c) Remove the wire harness. B073598E02 IR IR–14 INTERIOR – ROOF HEADLINING INSTALLATION HINT: A bolt without a torque specification is shown in the standard bolt chart (see page SS-2). 1. INSTALL ROOF HEADLINING ASSEMBLY (a) Align the markings, and then install the wire harness with tape. NOTICE: Attach the roof wire harness securely. (b) Install the silencer pads and headlining pad to the headlining. B076400E01 (c) Install the headlining with the 3 clips. 2. INSTALL VISOR HOLDER (a) Install the visor holder and turn it clockwise. 3. INSTALL VISOR ASSEMBLY LH (a) Connect the connector. B073598E02 (b) Install the visor with the 2 screws. 4. INSTALL VISOR ASSEMBLY RH HINT: Use the same procedures described for the LH side. 5. INSTALL ASSIST GRIP SUB-ASSEMBLY (a) Attach the 4 claws to install the assist grip. B075287E01 IR B076399E03 INTERIOR – ROOF HEADLINING 6. INSTALL ASSIST GRIP COVER (a) Attach the 4 claws to install the 2 covers. 7. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (a) Connect the room light connector. IR–15 B076398E03 (b) Attach the 4 claws to install the room light. B073597E02 (c) Attach the 4 claws to install the room light lens. 8. Claw Claw INSTALL MAP LIGHT ASSEMBLY (a) Connect the map light connector. Claw Claw B076772E04 (b) Attach the 4 clips to install the map light. (c) Install the 2 screws. IR B076771E03 IR–16 INTERIOR – ROOF HEADLINING 9. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (a) Attach the 6 clips and claw to install the inner garnish. 10. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH HINT: Use the same procedures described for the LH side. B073592E03 11. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (a) Attach the 7 claws and 3 clips to install the side panel. (b) Install the clip, screw and 2 bolts. Clip B073591E02 12. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (a) Attach the 6 claws and 2 clips to install the side panel. (b) Install the clip, screw and 2 bolts. Clip IR B079224E02 13. INSTALL REAR DECK TRIM COVER (a) Attach the 4 claws to install the trim cover. B076395E02 INTERIOR – ROOF HEADLINING IR–17 14. INSTALL REAR NO. 1 FLOOR BOARD (a) Attach the 5 clips to install the floor board. (b) Install the 2 clips, 2 bolts and 2 rope hooks. Rope Hook Clip 15. INSTALL DECK FLOOR BOX LH Clip 16. INSTALL REAR DECK FLOOR BOX 17. INSTALL REAR NO. 4 FLOOR BOARD 18. INSTALL REAR NO. 3 FLOOR BOARD 19. INSTALL REAR NO. 2 FLOOR BOARD 20. INSTALL TONNEAU COVER ASSEMBLY 21. INSTALL BACK DOOR WEATHERSTRIP B132619E01 22. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH (a) Connect the floor anchor with the bolt. Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf) 23. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH (a) Connect the floor anchor with the bolt. Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf) 24. INSTALL CENTER PILLAR GARNISH LH (a) Attach the clip to install the pillar garnish. (b) Install the 2 screws. 25. INSTALL CENTER PILLAR GARNISH RH HINT: Use the same procedures described for the LH side. B073590E02 26. INSTALL CENTER PILLAR LOWER GARNISH LH (a) Attach the 2 claws and 2 clips to the lower garnish. 27. INSTALL CENTER PILLAR LOWER GARNISH RH HINT: Use the same procedures described for the LH side. B073589E03 28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (a) Connect the floor anchor with the bolt. Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf) 29. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (a) Connect the floor anchor with the bolt. Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf) IR IR–18 INTERIOR – ROOF HEADLINING 30. INSTALL LAP BELT OUTER ANCHOR COVER (a) Attach the 3 claws to install the anchor cover. 31. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH 32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH B076394E03 33. INSTALL REAR SIDE SEATBACK FRAME LH (a) Attach the claw to install the frame. (b) Install the bolt. 34. INSTALL REAR SIDE SEATBACK FRAME RH HINT: Use the same procedures described for the LH side. B132620 35. INSTALL REAR DOOR SCUFF PLATE LH (a) Attach the 6 claws and clip to install the scuff plate. 36. INSTALL REAR DOOR SCUFF PLATE RH HINT: Use the same procedures described for the LH side. 37. INSTALL REAR SEAT CUSHION ASSEMBLY (See page SE-23) B073587E02 38. INSTALL FRONT PILLAR GARNISH LH (a) w/o Curtain Shield Airbag: Attach the 2 clips to install the pillar garnish. (b) w/ Curtain Shield Airbag: Remove the protective cover. IR B073594E03 IR–19 INTERIOR – ROOF HEADLINING (c) w/ Curtain Shield Airbag: Install the pillar garnish. (1) Set the claws of the pillar garnish to the area labeled C. (2) Insert the tip of clip A into the pillar garnish's hole. (3) Using needle-nose pliers, rotate the tip of clip A 90°. Then push the pillar garnish toward the vehicle body to attach the base of clip A and clip B. Pillar Garnish Clip A 90° Clip A 39. INSTALL FRONT PILLAR GARNISH RH HINT: Use the same procedures described for the LH side. Clip B C B132621E01 B 40. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH (a) Put protective tape as shown in the illustration. Standard measurement C A A Protective Tape Area Specified Condition A 2.0 mm (0.079 in.) B 10.0 mm (0.394 in.) C 50.0 mm (1.969 in.) (b) Attach the 5 claws to install the corner piece. Protective Tape 41. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH HINT: Use the same procedures described for the LH side. 42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH 43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH IR B136013E01 44. INSTALL COWL SIDE TRIM BOARD LH (a) Attach the claw and 2 clips to install the trim board. 45. INSTALL COWL SIDE TRIM BOARD RH HINT: Use the same procedures described for the LH side. B073588E02 IR–20 INTERIOR – ROOF HEADLINING 46. INSTALL FRONT DOOR SCUFF PLATE LH (a) Attach the 8 claws and 2 clips to install the scuff plate. 47. INSTALL FRONT DOOR SCUFF PLATE RH HINT: Use the same procedures described for the LH side. 48. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL B073586E02 IR 49. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. IR–20 INTERIOR – FUEL LID LOCK CONTROL FUEL LID LOCK CONTROL INTERIOR BODY COMPONENTS REAR SEAT CUSHION ASSEMBLY REAR SIDE SEATBACK ASSEMBLY LH FRONT SEAT ASSEMBLY LH ROOF SIDE INNER GARNISH ASSEMBLY LH CENTER PILLAR LOWER GARNISH LH DECK TRIM SIDE PANEL ASSEMBLY LH REAR DOOR SCUFF PLATE LH IR FRONT DOOR SCUFF PLATE LH FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY FUEL FILLER OPENING LID LOCK RETAINER FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY B132593E03 INTERIOR – FUEL LID LOCK CONTROL IR–21 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT SEAT ASSEMBLY LH (a) Remove the seat (see page SE-4). 3. REMOVE REAR SEAT CUSHION ASSEMBLY (See page SE-15) 4. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (See page SE-15) 5. REMOVE FRONT DOOR SCUFF PLATE LH (See page IR-7) 6. REMOVE REAR DOOR SCUFF PLATE LH (See page IR-9) 7. REMOVE CENTER PILLAR LOWER GARNISH LH (See page IR-9) 8. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (See page IR-11) 9. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (See page IR-11) 10. REMOVE FUEL LID LOCK OPEN LEVER SUBASSEMBLY (a) Remove the screw while holding the lever. (b) Disconnect the cable and remove the lever. Lever B074573E01 IR IR–22 INTERIOR – FUEL LID LOCK CONTROL 11. REMOVE FUEL LID LOCK CONTROL CABLE SUBASSEMBLY (a) Disconnect the cable from the clamps at the location shown in the illustration. Cable Cable Cable Cable Cable Cable Cable B075120E02 (b) Push the claw and pull out the cable. Cable IR Push B073318E04 INTERIOR – FUEL LID LOCK CONTROL IR–23 12. REMOVE FUEL FILLER OPENING LID LOCK RETAINER (a) Turn the lock retainer counterclockwise and remove the lock retainer as shown in the illustration. B073319E02 INSTALLATION 1. INSTALL FUEL FILLER OPENING LID LOCK RETAINER (a) Install the lock retainer and turn it clockwise as shown in the illustration. 2. INSTALL FUEL LID LOCK CONTROL CABLE SUBASSEMBLY (a) Attach the claw and install the cable to the lock retainer. Turn Retainer B073320E03 Cable Claw B073318E05 IR IR–24 INTERIOR – FUEL LID LOCK CONTROL (b) Connect the cable from the clamps at the location shown in the illustration. Cable Cable Cable Cable Cable Cable Cable B075120E02 3. INSTALL FUEL LID LOCK OPEN LEVER SUBASSEMBLY (a) Connect the cable to the lever. (b) Install the lever with the screw. Lever B074573E01 IR 4. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (See page IR-15) 5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (See page IR-15) 6. INSTALL CENTER PILLAR LOWER GARNISH LH (See page IR-17) 7. INSTALL REAR DOOR SCUFF PLATE LH (See page IR-18) 8. INSTALL FRONT DOOR SCUFF PLATE LH (See page IR-19) 9. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (See page SE-22) 10. INSTALL REAR SEAT CUSHION ASSEMBLY (See page SE-23) 11. INSTALL FRONT SEAT ASSEMBLY LH (a) Install the seat (see page SE-10). 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL INTERIOR – FUEL LID LOCK CONTROL IR–25 13. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. IR