ET–1 EXTERIOR – FRONT BUMPER FRONT BUMPER EXTERIOR BODY COMPONENTS FRONT BUMPER SIDE SUPPORT RH FRONT FENDER LINER RH FRONT BUMPER SIDE SUPPORT LH FRONT BUMPER ENERGY ABSORBER 67 (683, 49) FRONT FENDER LINER LH FRONT BUMPER REINFORCEMENT 5.0 (51, 44 in.*lbf) RADIATOR GRILLE PROTECTOR FRONT BUMPER COVER ET CENTER NO. 4 ENGINE UNDER COVER FRONT SPOILER COVER N*m (kgf*cm, ft.*lbf) : Specified torque B130311E04 ET–2 EXTERIOR – FRONT BUMPER RADIATOR GRILLE FRONT BUMPER MOULDING FRONT BUMPER COVER FRONT BUMPER EXTENSION MOUNTING BRACKET LOWER RADIATOR GRILLE RH FRONT TURN SIGNAL LIGHT MOUNTING BRACKET RH ET LOWER RADIATOR GRILLE LH FOG LIGHT UNIT RH (w/ Fog Light) FOG LIGHT UNIT LH (w/ Fog Light) B130313E03 EXTERIOR – FRONT BUMPER ET–3 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE FRONT FENDER LINER LH (a) Using a clip remover, remove the clip. (b) Partially remove the fender liner. HINT: It is not necessary to fully remove the fender liner. Partially remove it so that the bumper cover can be removed in a later step. 3. REMOVE FRONT FENDER LINER RH HINT: Use the same procedure described for the LH side. 4. REMOVE CENTER NO. 4 ENGINE UNDER COVER (a) Remove the 5 screws, 4 bolts and under cover. 5. REMOVE FRONT SPOILER COVER (a) Remove the 7 screws and spoiler cover. B130315 B130318 B130317 ET ET–4 EXTERIOR – FRONT BUMPER Radiator Grille Protector 6. REMOVE FRONT BUMPER COVER (a) Put protective tape under the front fender. (b) Using a clip remover, remove the 3 clips. (c) Remove the 2 radiator grille protectors and 4 screws. (d) Detach the 8 claws. Protective Tape B130316E01 (e) Detach the 4 claws and remove the bumper cover. (1) Hold the front bumper cover on its upper and lower parts with your hands as shown in the illustration. (2) Pull up the front bumper cover's lower part while holding its upper part securely. NOTICE: • The claw will not disengage unless the front bumper cover's upper part is securely held. • Do not forcibly pull up the front bumper. This will deform the claw. (f) w/ Fog light: Disconnect the 2 fog light connectors. Protective Tape B078079E02 ET 7. REMOVE FRONT BUMPER ENERGY ABSORBER 8. REMOVE FRONT BUMPER REINFORCEMENT (a) Using a screwdriver, remove the 4 wire harness clamps. HINT: Tape the screwdriver tip before use. (b) Remove the 4 nuts and reinforcement. 9. REMOVE FRONT BUMPER SIDE SUPPORT LH (a) Remove the 2 screws and side support. 10. REMOVE FRONT BUMPER SIDE SUPPORT RH (a) Remove the 2 screws and side support. DISASSEMBLY 1. B073580E01 REMOVE FRONT BUMPER MOULDING (a) Remove the 4 screws. (b) Using a screwdriver, detach the 4 claws and remove the moulding. HINT: Tape the screwdriver tip before use. EXTERIOR – FRONT BUMPER B073577E01 ET–5 2. REMOVE LOWER RADIATOR GRILLE LH (a) Using a screwdriver, detach the 4 claws and remove the grille. HINT: Tape the screwdriver tip before use. 3. REMOVE LOWER RADIATOR GRILLE RH HINT: Use the same procedure described for the LH side. 4. REMOVE FOG LIGHT UNIT LH (w/ Fog Light) (See page LI-87) 5. REMOVE FOG LIGHT UNIT RH (w/ Fog Light) HINT: Use the same procedure described for the LH side. 6. REMOVE RADIATOR GRILLE (a) Using a screwdriver, detach the 12 claws and remove the grille. HINT: Tape the screwdriver tip before use. 7. REMOVE FRONT TURN SIGNAL LIGHT MOUNTING BRACKET RH (a) Using a screwdriver, detach the claws and remove the mounting bracket. HINT: Tape the screwdriver tip before use. 8. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (a) Remove the 2 screws and mounting bracket. B073578E03 ET ET–6 EXTERIOR – FRONT BUMPER REASSEMBLY 1. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (a) Install the mounting bracket with the 2 screws. 2. INSTALL FRONT TURN SIGNAL LIGHT MOUNTING BRACKET RH (a) Attach the claws to install the mounting bracket. 3. INSTALL RADIATOR GRILLE (a) Attach the 12 claws to install the grille. 4. INSTALL FOG LIGHT UNIT LH (w/ Fog Light) (See page LI-88) 5. INSTALL FOG LIGHT UNIT RH (w/ Fog Light) HINT: Use the same procedure described for the LH side. 6. INSTALL LOWER RADIATOR GRILLE LH (a) Attach the 4 claws to install the grille. 7. INSTALL LOWER RADIATOR GRILLE RH HINT: Use the same procedure described for the LH side. 8. INSTALL FRONT BUMPER MOULDING (a) Attach the 4 claws to install the moulding. B073578E03 B073577E01 (b) Install the 4 screws. B073580E01 ET EXTERIOR – FRONT BUMPER ET–7 INSTALLATION HINT: A bolt without a torque specification is shown in the standard bolt chart (see page SS-2). 1. INSTALL FRONT BUMPER SIDE SUPPORT LH (a) Install the side support with 2 screws. 2. INSTALL FRONT BUMPER SIDE SUPPORT RH (a) Install the side support with 2 screws. 3. INSTALL FRONT BUMPER REINFORCEMENT (a) Install the reinforcement with the 4 nuts. Torque: 67 N*m (683 kgf*cm, 49 ft.*lbf) (b) Install the 4 wire harness clamps. 4. INSTALL FRONT BUMPER ENERGY ABSORBER 5. INSTALL FRONT BUMPER COVER (a) Put protective tape under the front fender. (b) w/ Fog light: Connect the 2 fog light connectors. (c) Attach the 12 claws to install the bumper cover. (d) Install the 4 screws and 3 clips. (e) Install the 2 radiator grille protectors. Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 6. INSTALL FRONT SPOILER COVER (a) Install the spoiler cover with the 7 screws. Radiator Grille Protector Protective Tape B132997E01 ET B130317 7. B130318 INSTALL CENTER NO. 4 ENGINE UNDER COVER (a) Install the under cover with the 5 screws and 4 bolts. ET–8 EXTERIOR – FRONT BUMPER 8. INSTALL FRONT FENDER LINER LH (a) Install the fender liner with the clip. 9. INSTALL FRONT FENDER LINER RH HINT: Use the same procedure described for the LH side. 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL B130315 ET 11. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. ET–8 EXTERIOR – REAR BUMPER REAR BUMPER EXTERIOR BODY COMPONENTS REAR BUMPER REINFORCEMENT SUB-ASSEMBLY REAR BUMPER ARM SUB-ASSEMBLY RH REAR BUMPER SIDE RETAINER RH REAR BUMPER ARM SUB-ASSEMBLY LH REAR BUMPER CENTER BRACKET REAR BUMPER ENERGY ABSORBER REAR BUMPER SIDE RETAINER LH REAR BUMPER COVER STOPPER ET REAR NO. 1 SPOILER REAR SIDE SPOILER RH REAR SIDE SPOILER LH B132594E01 ET–9 EXTERIOR – REAR BUMPER REMOVAL HINT: When replacing the spoiler, heat the bumper cover and spoiler using a heat light. Standard heating temperature Item Specified Condition Spoiler 40 to 60°C (104 to 140°F) Bumper cover 20 to 30°C (68 to 86°F) NOTICE: Do not heat the bumper cover and spoiler excessively. 1. Protective Tape REMOVE REAR BUMPER COVER (a) Put protective tape under the quarter panel. (b) Remove the 5 screws, nut and 2 stoppers. (c) Using a clip remover, remove the 4 clips. (d) Using a screwdriver, detach the 10 claws. HINT: Tape the screwdriver tip before use. B088175E03 (e) Detach the 2 claws and remove the bumper cover. (1) Hold the rear bumper cover on its upper and lower parts with your hands as shown in the illustration. (2) Pull up the rear bumper cover's lower part while holding its upper part securely. NOTICE: • The claw will not detach unless the rear bumper cover's upper part is securely held. • Do not forcibly pull up the rear bumper. This will deform the claw. B088176E02 2. REMOVE REAR SIDE SPOILER LH (a) Using a screwdriver, remove the 2 retainers. HINT: Tape the screwdriver tip before use. (b) Remove the 2 clips and 3 screws. ET B078273E01 ET–10 EXTERIOR – REAR BUMPER (c) Put protective tape under the rear bumper cover. (d) Using a heat light, heat the spoiler. NOTICE: Do not heat the spoiler excessively. (e) Cut the double-sided tape that holds the spoiler to the bumper cover with a knife. NOTICE: • If reusing the spoiler, take care not to damage the spoiler. • Be careful not to damage the bumper cover. (f) Remove the spoiler. Protective Tape Double-sided Tape B079593E01 3. REMOVE REAR SIDE SPOILER RH HINT: Use the same procedures described for the LH side. 4. REMOVE REAR NO. 1 SPOILER (a) Using a clip remover, remove the 5 clips. B078276E01 (b) Put protective tape under the rear bumper cover. (c) Using a heat light, heat the spoiler. NOTICE: Do not heat the spoiler excessively. (d) Cut the double-sided tape that holds the spoiler to the bumper cover with a knife. NOTICE: • If reusing the spoiler, take care not to damage the spoiler. • Be careful not to damage the bumper cover. (e) Remove the spoiler. Protective Tape Double-sided Tape B079449E01 ET 5. REMOVE REAR BUMPER ENERGY ABSORBER 6. REMOVE REAR BUMPER CENTER BRACKET 7. REMOVE REAR BUMPER REINFORCEMENT SUBASSEMBLY (a) Remove the 4 nuts and reinforcement. 8. REMOVE REAR BUMPER ARM SUB-ASSEMBLY LH (a) Remove the 2 bolts and bumper arm. 9. REMOVE REAR BUMPER ARM SUB-ASSEMBLY RH (a) Remove the 2 bolts and bumper arm. 10. REMOVE REAR BUMPER SIDE RETAINER LH (a) Remove the 2 screws and side retainer. 11. REMOVE REAR BUMPER SIDE RETAINER RH (a) Remove the 2 screws and side retainer. ET–11 EXTERIOR – REAR BUMPER INSTALLATION HINT: • A bolt without a torque specification is shown in the standard bolt chart (see page SS-2). • When installing the spoiler, heat the bumper cover and spoiler using a heat light. Standard heating temperature Item Specified Condition Spoiler 40 to 60°C (104 to 140°F) Bumper cover 20 to 30°C (68 to 86°F) NOTICE: Do not heat the bumper cover and spoiler excessively. 1. INSTALL REAR BUMPER SIDE RETAINER LH (a) Install the side retainer with the 2 screws. 2. INSTALL REAR BUMPER SIDE RETAINER RH (a) Install the side retainer with the 2 screws. 3. INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH (a) Install the bumper arm with the 2 bolts. 4. INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH (a) Install the bumper arm with the 2 bolts. 5. INSTALL REAR BUMPER REINFORCEMENT SUBASSEMBLY (a) Install the reinforcement with the 4 nuts. 6. INSTALL REAR BUMPER CENTER BRACKET 7. INSTALL REAR BUMPER ENERGY ABSORBER 8. INSTALL REAR NO. 1 SPOILER (a) Clean the bumper cover surface. (1) Using a heat light, heat the bumper cover. NOTICE: Do not heat the bumper cover excessively. (2) Remove the double-sided tape from the bumper cover. (3) Wipe off any tape adhesive residue with white gasoline. (b) If reusing the spoiler: Clean the spoiler and install new double-sided tape. (1) Using a heat light, heat the spoiler. NOTICE: Do not heat the spoiler excessively. (2) Remove the double-sided tape from the spoiler. (3) Wipe off any tape adhesive residue with white gasoline. (4) Install new double-sided tape to the spoiler. NOTICE: Install the double-sided tape exactly according to the specifications below. ET ET–12 EXTERIOR – REAR BUMPER 0.8 mm (0.031 in.) A Double-sided Tape 4.0 mm (0.157 in.) A A-A B079450E03 (c) Install the spoiler. (1) Using a heat light, heat the bumper cover and spoiler. NOTICE: Do not heat the bumper cover and spoiler excessively. (2) Remove the peeling paper from the face of the spoiler. NOTICE: After removing the peeling paper, keep the exposed adhesive free from foreign matter. (3) Install the spoiler with the 5 clips. NOTICE: Do not apply excessive force to the spoiler. Apply steady pressure with your thumbs. 9. ET INSTALL REAR SIDE SPOILER LH (a) Clean the bumper cover surface. (1) Using a heat light, heat the bumper cover. NOTICE: Do not heat the bumper cover excessively. (2) Remove the double-sided tape from the bumper cover. (3) Wipe off any tape adhesive residue with white gasoline. (b) If reusing the spoiler: Clean the spoiler and install new double-sided tape. (1) Using a heat light, heat the spoiler. NOTICE: Do not heat the spoiler excessively. (2) Remove the double-sided tape from the spoiler. (3) Wipe off any tape adhesive residue with white gasoline. (4) Install new double-sided tape to the spoiler. NOTICE: Install the double-sided tape exactly according to the specifications below. ET–13 EXTERIOR – REAR BUMPER 50.0 mm (1.969 in.) 100.0 mm (3.937 in.) 150.0 mm (5.906 in.) 0.8 mm (0.031 in.) A Double-sided Tape A 4.0 mm (0.157 in.) Double-sided Tape A-A B079451E03 (c) Install the spoiler. (1) Using a heat light, heat the bumper cover and spoiler. NOTICE: Do not heat the bumper cover and spoiler excessively. (2) Remove the peeling paper from the face of the spoiler. NOTICE: After removing the peeling paper, keep the exposed adhesive free from foreign matter. (3) Install the spoiler with the 2 retainers, 2 clips and 3 screws. NOTICE: Do not apply excessive force to the spoiler. Apply steady pressure with your thumbs. 10. INSTALL REAR SIDE SPOILER RH HINT: Use the same procedures for the LH side. B078273E01 11. REMOVE REAR BUMPER COVER (a) Put protective tape under the quarter panel. (b) Attach the 12 claws to install the bumper cover. (c) Install the 4 clips, 5 screws, nut and 2 stoppers. Protective Tape B132595E01 ET ET–14 EXTERIOR – NAME PLATE NAME PLATE REPLACEMENT 1. INSTALL NAME PLATE 1 2 3 Body R End R End 1 B A C D Body R End K 2 ET E L 3 F H G J I B076801E03 ET–15 EXTERIOR – NAME PLATE Standard measurement Area Specified Condition Area Specified Condition A 74.1 mm (2.917 in.) G 66.2 mm (2.606 in.) B 48.6 mm (1.913 in.) H 32.0 mm (1.620 in.) C 114.0 mm (4.488 in.) I 99.6 mm (3.921 in.) D 89.1 mm (3.508 in.) J 36.2 mm (1.425 in.) E 61.0 mm (2.402 in.) K 36.9 mm (1.453 in.) F 115.1 mm (4.531 in.) L 64.5 mm (2.540 in.) ET ET–16 EXTERIOR – REAR SPOILER REAR SPOILER EXTERIOR BODY COMPONENTS REAR SPOILER SUB-ASSEMBLY BACK DOOR UPPER TRIM BOARD ASSEMBLY CENTER STOP LIGHT ASSEMBLY 5.5 (56, 49 in.*lbf) BACK DOOR LOWER TRIM BOARD ASSEMBLY 5.5 (56, 49 in.*lbf) REAR WIPER MOTOR ASSEMBLY ET REAR WIPER ARM ASSEMBLY REAR WIPER MOTOR GROMMET N*m (kgf*cm, ft.*lbf) : Specified torque B132618E03 EXTERIOR – REAR SPOILER ET–17 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE REAR WIPER ARM ASSEMBLY (See page WW-22) 3. REMOVE BACK DOOR LOWER TRIM BOARD ASSEMBLY (See page ED-43) 4. REMOVE BACK DOOR UPPER TRIM BOARD ASSEMBLY (See page ED-44) 5. REMOVE REAR WIPER MOTOR ASSEMBLY (See page WW-22) 6. REMOVE REAR SPOILER SUB-ASSEMBLY (a) Put protective tape under the rear spoiler. (b) Remove the 4 bolts. (c) Using a screwdriver, detach the 3 clips and remove the rear spoiler. HINT: Tape the screwdriver tip before use. (d) Disconnect the center stop light connector. 7. REMOVE CENTER STOP LIGHT ASSEMBLY (See page LI-94) Protective Tape B076775E01 ET ET–18 EXTERIOR – REAR SPOILER INSTALLATION Protective Tape 1. INSTALL CENTER STOP LIGHT ASSEMBLY (See page LI-94) 2. INSTALL REAR SPOILER SUB-ASSEMBLY (a) Put protective tape under the rear spoiler. (b) Connect the center stop light connector. (c) Attach the 3 clips to install the rear spoiler. (d) Install the 4 bolts. 3. INSTALL REAR WIPER MOTOR ASSEMBLY (See page WW-22) 4. INSTALL BACK DOOR UPPER TRIM BOARD ASSEMBLY (See page ED-48) 5. INSTALL BACK DOOR LOWER TRIM BOARD ASSEMBLY (See page ED-48) 6. INSTALL REAR WIPER ARM ASSEMBLY (See page WW-23) 7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 8. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. B076775E02 ET ET–19 EXTERIOR – FRONT DOOR BELT MOULDING FRONT DOOR BELT MOULDING EXTERIOR BODY COMPONENTS OUTER REAR VIEW MIRROR ASSEMBLY LH FRONT DOOR BELT MOULDING ASSEMBLY LH DOOR PULL HANDLE 5.5 (56, 49 in.*lbf) FRONT DOOR LOWER FRAME BRACKET GARNISH LH FRONT DOOR INSIDE HANDLE BEZEL LH FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH ET FRONT ARMREST UPPER BASE PANEL LH N*m (kgf*cm, ft.*lbf) : Specified torque B132610E02 ET–20 EXTERIOR – FRONT DOOR BELT MOULDING REMOVAL HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. Protective Tape ET Moulding Remover B074194E02 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See page ED-11) 3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH (See page ED-11) 4. REMOVE DOOR PULL HANDLE (See page ED-11) 5. REMOVE FRONT ARMREST UPPER BASE PANEL LH (See page ED-11) 6. REMOVE FRONT DOOR TRIM BOARD SUBASSEMBLY LH (See page ED-12) 7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH (See page MI-9) 8. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH (a) Put protective tape under the moulding. (b) Using a moulding remover, detach the claws to remove the moulding as shown in the illustration. HINT: Tape the remover tip before use. EXTERIOR – FRONT DOOR BELT MOULDING ET–21 INSTALLATION HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. 1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH (a) Attach the claws to install the moulding. HINT: Confirm that the moulding is firmly installed. 2. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH (See page MI-13) 3. INSTALL FRONT DOOR TRIM BOARD SUBASSEMBLY LH (See page ED-21) 4. INSTALL FRONT ARMREST UPPER BASE PANEL LH (See page ED-21) 5. INSTALL DOOR PULL HANDLE (See page ED-22) 6. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH (See page ED-22) 7. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See page ED-22) 8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 9. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. B132614 ET ET–22 EXTERIOR – REAR DOOR BELT MOULDING REAR DOOR BELT MOULDING EXTERIOR BODY COMPONENTS DOOR PULL HANDLE REAR DOOR BELT MOULDING ASSEMBLY LH REAR DOOR TRIM BOARD SUB-ASSEMBLY LH ET REAR DOOR ARMREST UPPER BASE PANEL LH REAR DOOR INSIDE HANDLE BEZEL LH B132612E02 EXTERIOR – REAR DOOR BELT MOULDING ET–23 REMOVAL HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH (See page ED-28) 3. REMOVE DOOR PULL HANDLE (See page ED-28) 4. REMOVE REAR DOOR ARMREST UPPER BASE PANEL LH (See page ED-28) 5. REMOVE REAR DOOR TRIM BOARD SUBASSEMBLY LH (See page ED-28) 6. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH (a) Put protective tape under the moulding. (b) Using a moulding remover, detach the claws to remove the moulding as shown in the illustration. HINT: Tape the remover tip before use. Protective Tape Moulding Remover B074179E02 ET ET–24 EXTERIOR – REAR DOOR BELT MOULDING INSTALLATION HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. 1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH (a) Attach the claws to install the moulding. HINT: Confirm that the moulding is firmly installed. 2. INSTALL REAR DOOR TRIM BOARD SUBASSEMBLY LH (See page ED-37) 3. INSTALL REAR DOOR ARMREST UPPER BASE PANEL LH (See page ED-37) 4. INSTALL DOOR PULL HANDLE (See page ED-37) 5. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH (See page ED-37) 6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 7. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. B132613 ET EXTERIOR – ROOF DRIP SIDE FINISH MOULDING ET–25 ROOF DRIP SIDE FINISH MOULDING EXTERIOR BODY COMPONENTS ROOF DRIP SIDE FINISH MOULDING LH ROOF DRIP SIDE FINISH MOULDING CLIP ROOF DRIP SIDE FINISH MOULDING CLIP Non-reusable part B132616E04 ET ET–26 EXTERIOR – ROOF DRIP SIDE FINISH MOULDING REMOVAL HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. 1. Protective Tape B074186E02 ET REMOVE ROOF DRIP SIDE FINISH MOULDING LH (a) Put protective tape around the edges of the moulding. (b) Using a moulding remover, detach the moulding's front and rear end 2 clips and remove the moulding. NOTICE: • Do not remove the clips from the vehicle body. • If the clips are damaged or removed accidentally, replace them. EXTERIOR – ROOF DRIP SIDE FINISH MOULDING ET–27 INSTALLATION HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. • When replacing the clip, heat the vehicle body and clip using a heat light. Standard heating temperature Item Specified Condition Vehicle body 40 to 60°C (104 to 140°F) Clip 20 to 30°C (68 to 86°F) NOTICE: Do not heat the clip and vehicle body excessively. 1. Front REPLACE ROOF DRIP SIDE FINISH MOULDING CLIP HINT: Use the procedures below to replace damaged or accidentally removed clips. If this step is not necessary, go to the next step. NOTICE: After press-fitting the clips, wait 30 minutes or more before installing the moulding. HINT: • Minimum hardening time: 30 minutes • Time needed for complete hardening: 24 hours (a) Remove the double-sided tape that remains on the surfaces of the moulding and vehicle body, and then clean the surface with white gasoline. (b) Using a heat light, heat the clip installation surface of the vehicle body and installation part of the clips. (c) Install new clips to the positions shown in the illustration. Press-fit the clips by hand. Clip 1.6 mm (0.063 in.) R end Rear ET Clip 9.2 mm (0.362 in.) R end mm (in.) B076907E02 ET–28 EXTERIOR – ROOF DRIP SIDE FINISH MOULDING 2. Protective Tape B074186E02 ET INSTALL ROOF DRIP SIDE FINISH MOULDING LH (a) Put protective tape around the edges of the moulding. (b) Adjust the position of the moulding so that the front and rear ends attach to the vehicle's 2 clips, and install the moulding. (c) Remove the protective tape. ET–28 EXTERIOR – SIDE MUDGUARD SIDE MUDGUARD EXTERIOR BODY COMPONENTS SIDE MUDGUARD LH ET RETAINER REAR WHEEL HOUSE FRONT PLATE LH B132596E05 EXTERIOR – SIDE MUDGUARD ET–29 REMOVAL HINT: • Use the same procedures for the LH side and RH side. • The procedures listed below are for the LH side. 1. REMOVE REAR WHEEL HOUSE FRONT PLATE LH (a) Remove the screw and front plate. 2. REMOVE SIDE MUDGUARD LH (a) Remove the screw and 8 retainers. (b) Detach the clip and remove the mudguard. B074189E01 B074190E02 ET ET–30 EXTERIOR – SIDE MUDGUARD INSTALLATION HINT: • Use the same procedures for the LH side and RH side. • The procedures listed below are for the LH side. 1. INSTALL SIDE MUDGUARD LH (a) Attach the clip to install the mudguard. (b) Install the screw and 8 retainers. B074190E02 2. B074189E01 ET INSTALL REAR WHEEL HOUSE FRONT PLATE LH (a) Install the front plate with the screw. EXTERIOR – FRONT DOOR WINDOW FRAME MOULDING ET–31 FRONT DOOR WINDOW FRAME MOULDING EXTERIOR BODY COMPONENTS FRONT DOOR WINDOW FRAME REAR MOULDING LH B132609E02 ET ET–32 EXTERIOR – FRONT DOOR WINDOW FRAME MOULDING REMOVAL HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. • When removing the moulding, heat the vehicle body and moulding using a heat light. Standard heating temperature Item Specified Condition Vehicle Body 40 to 60°C (104 to 140°F) Moulding 20 to 30°C (68 to 86°F) NOTICE: Do not heat the vehicle body and moulding excessively. 1. Double-sided Tape B074180E02 ET REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING LH (a) Remove the screw. (b) Using a heat light, heat the moulding and vehicle body. (c) Cut the double-sided tape that holds the moulding to the vehicle body with a knife. NOTICE: • If reusing the moulding, take care not to damage the moulding. • Be careful not to damage the vehicle body. (d) Remove the moulding. EXTERIOR – FRONT DOOR WINDOW FRAME MOULDING ET–33 INSTALLATION HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. • When installing the moulding, heat the vehicle body and moulding using a heat light. Standard heating temperature Item Specified Condition Vehicle Body 40 to 60°C (104 to 140°F) Moulding 20 to 30°C (68 to 86°F) NOTICE: Do not heat the vehicle body and moulding excessively. 1. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING LH (a) Clean the vehicle body surface. (1) Using a heat light, heat the vehicle body. (2) Remove the double-sided tape from the vehicle body. (3) Wipe off any tape adhesive residue with white gasoline. (b) If reusing the moulding: Clean the moulding and install new double-sided tape. (1) Using a heat light, heat the moulding. (2) Remove the double-sided tape from the moulding. (3) Wipe off any tape adhesive residue with white gasoline. (4) Install new double-sided tape to the moulding. NOTICE: Install the double-sided tape exactly according to the specifications below. Standard measurement (2) (1) A B C B074182E03 Area Specified Condition A (1) 440.0 mm (17.323 in.) (2) 37.0 mm (1.457 in.) B 5.0 mm (0.197 in.) C 0.8 mm (0.032 in.) (c) Install the moulding. (1) Using a heat light, heat the vehicle body and moulding. (2) Remove the peeling paper from the face of the moulding. NOTICE: After removing the peeling paper, keep the exposed adhesive free from foreign matter. (3) Install the moulding with the screw. NOTICE: Do not apply excessive force to the moulding. Apply steady pressure with your thumbs. ET ET–34 EXTERIOR – REAR DOOR WINDOW FRAME MOULDING REAR DOOR WINDOW FRAME MOULDING EXTERIOR BODY COMPONENTS REAR DOOR WINDOW FRAME FRONT MOULDING LH B132611E02 ET EXTERIOR – REAR DOOR WINDOW FRAME MOULDING ET–35 REMOVAL HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. • When removing the moulding, heat the vehicle body and moulding using a heat light. Standard heating temperature Item Specified Condition Vehicle Body 40 to 60°C (104 to 140°F) Moulding 20 to 30°C (68 to 86°F) NOTICE: Do not heat the vehicle body and moulding excessively. 1. Double-sided Tape B074181E02 REMOVE REAR DOOR WINDOW FRAME FRONT MOULDING LH (a) Remove the screw. (b) Using a heat light, heat the moulding and vehicle body. (c) Cut the double-sided tape that holds the moulding to the vehicle body with a knife. NOTICE: • If reusing the moulding, take care not to damage the moulding. • Be careful not to damage the vehicle body. (d) Remove the moulding. ET ET–36 EXTERIOR – REAR DOOR WINDOW FRAME MOULDING INSTALLATION HINT: • Use the same procedures for the RH side and LH side. • The procedures listed below are for the LH side. • When installing the moulding, heat the vehicle body and moulding using a heat light. Standard heating temperature Item Specified Condition Vehicle Body 40 to 60°C (104 to 140°F) Moulding 20 to 30°C (68 to 86°F) NOTICE: Do not heat the vehicle body and moulding excessively. 1. (4) Install new double-sided tape to the moulding. NOTICE: Install the double-sided tape exactly according to the specifications below. Standard measurement (2) (1) INSTALL REAR DOOR WINDOW FRAME FRONT MOULDING LH (a) Clean the vehicle body surface. (1) Using a heat light, heat the vehicle body. (2) Remove the double-sided tape from the vehicle body. (3) Wipe off any tape adhesive residue with white gasoline. (b) If reusing the moulding: Clean the moulding and install new double-sided tape. (1) Using a heat light, heat the moulding. (2) Remove the double-sided tape from the moulding. (3) Wipe off any tape adhesive residue with white gasoline. Area Specified Condition A (1) 360.0 mm (14.173 in.) (2) 37.0 mm (1.457 in.) (3) 440.0 mm (17.322 in.) B 5.0 mm (0.197 in.) C (1) 1.2 mm (0.047 in.) (2) 0.8 mm (0.032 in.) (3) 0.8 mm (0.032 in.) (3) ET A B C B074183E03 (c) Install the moulding. (1) Using a heat light, heat the vehicle body and moulding. (2) Remove the peeling paper from the face of the moulding. NOTICE: After removing the peeling paper, keep the exposed adhesive free from foreign matter. EXTERIOR – REAR DOOR WINDOW FRAME MOULDING ET–37 (3) Install the moulding with the screw. NOTICE: Do not apply excessive force to the moulding. Apply steady pressure with your thumbs. ET EXTERIOR – BACK DOOR OUTSIDE GARNISH ET–37 BACK DOOR OUTSIDE GARNISH EXTERIOR BODY COMPONENTS BACK DOOR OUTSIDE GARNISH BACK DOOR LOWER TRIM BOARD ASSEMBLY BACK DOOR OPENER SWITCH ASSEMBLY B132615E03 ET ET–38 EXTERIOR – BACK DOOR OUTSIDE GARNISH REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE BACK DOOR LOWER TRIM BOARD ASSEMBLY (See page ED-48) 3. REMOVE BACK DOOR OUTSIDE GARNISH (a) Disconnect the back door opener switch connector. (b) Remove the 4 nuts. Nut Nut Nut B133842E01 (c) Using a screwdriver, detach the 2 clips and remove the garnish (with back door opener switch). HINT: Tape the screwdriver tip before use. (d) Remove the 2 screws and back door opener switch from the garnish. ET B067629E01 ET–39 EXTERIOR – BACK DOOR OUTSIDE GARNISH INSTALLATION 1. INSTALL BACK DOOR OUTSIDE GARNISH (a) Install the back door opener switch to the garnish with the 2 screws. (b) Attach the 2 clips to install the garnish. B067629E01 Nut Nut Nut B133842E01 (c) Install the 4 nuts. (d) Connect the back door opener switch connector. 2. INSTALL BACK DOOR LOWER TRIM BOARD ASSEMBLY (See page ED-48) 3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 4. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. ET