1NZ-FXE FUEL – FUEL SYSTEM FU–1 FUEL SYSTEM PRECAUTION 1. 2. A088352E01 PRECAUTION (a) Before working on the fuel system, disconnect the cable from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. (b) Do not work on the fuel system near fire. Never smoke while performing work. (c) Keep rubber or leather parts away from gasoline. DISCHARGE FUEL SYSTEM PRESSURE CAUTION: • Before removing the fuel system parts, take precautions to prevent gasoline spillage. • As some pressure remains in the fuel line even after taking precautions to prevent gasoline spillage, use a shop rag to prevent gasoline from spilling when disconnecting the fuel line. (a) Set the vehicle to the "INSPECTION MODE1" (see page IN-34). (b) Disconnect the cable from negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. (c) Remove the rear seat cushion (see page SE-15). (d) Remove the rear floor service hole cover. (e) Disconnect the fuel pump connector. (f) Connect the cable to the negative (-) battery terminal. (g) Start the engine. (h) After the engine stops (rough idle), turn the power switch OFF. HINT: DTC P0171 (system to lean) may be present. (i) Crank the engine again, then check that the engine does not start. (j) Remove the fuel tank cap, then discharge the pressure in the fuel tank completely. (k) Disconnect the cable from the negative (-) battery terminal. (l) Connect the fuel pump connector. (m) Install the rear floor service hole cover. (n) Install the rear seat cushion (see page SE-23). (o) Connect the cable to the negative (-) battery terminal.. FU FU–2 1NZ-FXE FUEL – FUEL SYSTEM (p) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. 3. Plastic Bag A088338E04 FU CORRECT INCORRECT O-Ring FUEL SYSTEM (a) When disconnecting the high-pressure fuel line, a large amount of gasoline will spill out. So take the following precautions. (1) Discharge the fuel system pressure (see step DISCHARGE FUEL SYSTEM PRESSURE). (2) Disconnect the fuel pump tube. (3) Drain the pressure remaining in the fuel pump tube. (4) Cover the disconnected fuel pump tube (fuel tube joint and fuel tube connector) with a plastic bag to prevent damage and intrusion of foreign objects. (b) Take the following precautions when removing and installing the fuel injector. (1) Do not reuse the O-ring. (2) Do not damage a new O-ring when installing it to the fuel injector. (3) Before installing a new O-ring, apply spindle oil or gasoline. NOTICE: Do not use engine oil, gear oil or brake oil. INCORRECT Fuel Delivery Pipe A112283E02 Insulator O-Ring Fuel Delivery Pipe A088333E02 (c) Install the fuel injector to the fuel delivery pipe and cylinder head as illustrated. NOTICE: Apply spindle oil or gasoline to the contact surface of the fuel delivery pipe and fuel injector before installing the fuel injector. 1NZ-FXE FUEL – FUEL SYSTEM Retainer Pinch Pull Out FU–3 (d) Take the following precautions when removing the fuel tube connector (Type A). (1) Check the fuel tube connector and pipe for dirt or mud before removing the fuel tube connector. If they are dirty, wipe them off with a shop rag. (2) Pinch the retainer as illustrated, then pull out the fuel tube connector from the pipe. Pinch A088336E14 (3) If the fuel tube connector and pipe are stuck, pinch the pipe, then push and pull the fuel tube connector to release and disconnect the fuel tube connector. NOTICE: Do not use any tools. (4) After removing the fuel tube, check the sealing surface of the pipe for dirt or mud. If it dirty, wipe it off with a shop rag. A088337E02 Plastic Bag (5) Cover the disconnected fuel tube connector and pipe with a plastic bag to prevent damage and intrusion of foreign objects. A088338E05 (e) Take the following precautions when installing the fuel tube connector (Type A). (1) Align the fuel tube connector with the pipe, then push in the fuel tube connector until the retainer makes a "click" sound. HINT: If they are connected too tightly, apply a light coat of engine oil to the tip of the pipe, then install the fuel tube connector. Push A088339E04 (2) After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by pulling them. Pull A088340E03 FU FU–4 1NZ-FXE FUEL – FUEL SYSTEM (f) Pinch Retainer Take the following precautions when removing the fuel tube connector (Type B). (1) Check the fuel tube connector and pipe for dirt or mud before removing the fuel tube connector. If they are dirty, wipe them off with a shop rag. (2) Pinch the retainer as illustrated, then pull out the fuel tube connector from the pipe. Pinch Pull Out A088341E05 (3) If the fuel connector and pipe are stuck, pinch the pipe, then push and pull the fuel tube connector to release and disconnect the fuel tube connector. NOTICE: Do not use any tools. (4) After removing the fuel tube, check the sealing surface of the pipe for dirt or mud. If it is dirty, wipe it off with a shop rag. FU A088343E04 (5) Cover the disconnected fuel tube connector and pipe with a plastic bag to prevent damage and intrusion of foreign objects. Plastic Bag A093867E02 (g) Take the following precautions when installing the fuel tube connector (Type B). (1) Align the fuel tube connector with the pipe, then push in the fuel tube connector until the retainer makes a "click" sound. HINT: If they are connected too tightly, apply a light coat of engine oil to the tip of the pipe, then install the fuel tube connector. A088344E01 4. A088345E04 (2) After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by pulling them. CHECK FOR FUEL LEAKS (a) Check that there are no fuel leaks after doing maintenance on the fuel system (see page FU-7). FU–5 1NZ-FXE FUEL – FUEL SYSTEM PARTS LOCATION POWER SOURCE CONTROL ECU ECM FU FUEL TANK ENGINE ROOM RELAY BLOCK, JUNCTION BLOCK - INTEGRATION RELAY (UNIT B: IG2 RELAY) (UNIT C: C/OPN RELAY) - AM2 FUSE - P/I H-FUSE DRIVER SIDE JUNCTION BLOCK - IGN FUSE FUEL INJECTOR A112282E01 FU–6 1NZ-FXE FUEL – FUEL SYSTEM SYSTEM DIAGRAM ECM Integration Relay (Unit B) IG2 No. 1 Fuel Injector AM2 #10 No. 2 Fuel Injector #20 FU Power Source Control ECU No. 3 Fuel Injector #30 IG2D No. 4 Fuel Injector #40 from P/I H-Fuse +B Integration Relay (Unit B) C/OPN from IGN Fuse FC Fuel Pump E1 A112330E01 1NZ-FXE FUEL – FUEL SYSTEM FU–7 ON-VEHICLE INSPECTION 1. Fuel Tube Connector Cutter Knife Protector A112284E01 CHECK FUEL PRESSURE (a) Prepare for the inspection. (1) Prepare a new fuel tube. HINT: Part No. 23901-21081 (2) Using a cutter knife, cut off the protector of the fuel tube as illustrated. Tear off the protector by hand, then remove the fuel tube connector. NOTICE: If the protector is cut too deeply using the cutter, the O-ring of the fuel tube connector will be damaged. (b) Discharge fuel system pressure (see page FU-12). (c) Using a voltmeter, measure the battery voltage. Standard voltage: 9.0 to 14 V (d) Disconnect the cable from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. (e) Disconnect the fuel tube (see page FU-14). (f) SST (Pressure Gauge) SST (Hose) Fuel Tube SST (T-joint) SST (Hose) Fuel Tube Connector A112285E01 Install SST and the fuel tube connector to the vehicle. SST 09268-41047 (95336-08070), 09268-45014 (09268-41200, 09268-41220, 09268-41250) (g) Wipe off any spilt gasoline. (h) Connect the cable to the negative battery terminal. FU FU–8 1NZ-FXE FUEL – FUEL SYSTEM (i) Connect the intelligent tester (with CAN VIM) to the DLC3. (j) Measure the fuel pressure. Standard: 304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi) • If the fuel pressure is greater than the standard value, replace the fuel tank. • If the fuel pressure is less than the standard value, check the connection of the fuel hose and fuel tank. (k) Disconnect the intelligent tester from the DLC3. (l) Set the vehicle to inspection mode (see page IN34). (m) Start the engine. (n) Measure the fuel pressure at idle. Standard: 304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi) (o) Stop the engine. (p) After stopping the engine, check that the fuel pressure does not change for 5 minutes. Standard: 147 kPa (1.5 kgf/cm2, 21 psi) or more If the fuel pressure is not as specified, check the fuel tank or fuel injectors (see page FU-15). (q) After measuring the fuel pressure, disconnect the cable from the negative battery terminal. Remove SST and the fuel tube connector while taking care to prevent spilling gasoline. (r) Connect the fuel tube (see page FU-18). Intelligent Tester CAN VIM DLC3 A087542E05 FU 2. CHECK FUEL PUMP (a) Connect the intelligent tester (with CAN VIM) to the DLC3. (b) Turn the power switch ON (IG). NOTICE: Do not start the engine. (c) Turn the intelligent tester ON. (d) Select the item: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD. (e) Check the fuel pump operation while operating it with the intelligent tester. If the fuel pump does not operate, replace the fuel tank. 3. CHECK FOR FUEL LEAKS (a) Check that there are no leaks in the fuel system while fuel pressure is applied. Intelligent Tester CAN VIM DLC3 A087542E05 FU–9 1NZ-FXE FUEL – FUEL INJECTOR FUEL INJECTOR 1NZ-FXE FUEL ENGINE COMPONENTS WINDSHIELD WIPER ARM COVER 21 (214, 16) 21 (214, 16) x2 FRONT WIPER ARM LH FU FRONT WIPER ARM RH HOOD TO COWL TOP SEAL COWL TOP VENTILATION LOUVER RH x5 5.5 (56, 49 in.*lbf) COWL TOP VENTILATION LOUVER LH WINDSHIELD WIPER MOTOR AND LINK WINDSHIELD WIPER MOTOR CONNECTOR 6.4 (65, 57 in.*lbf) x7 8.4 (86, 74 in.*lbf) x2 NO. 2 ENGINE ROOM RELAY BLOCK N*m (kgf*cm, ft.*lbf) : Specified torque FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY A112286E01 FU–10 1NZ-FXE FUEL – FUEL INJECTOR AIR CLEANER ASSEMBLY NO. 1 AIR CLEANER INLET 7.0 (71, 62 in.*lbf) x2 BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY 8.5 (87, 75 in.*lbf) FU x2 3.0 (31, 27 in.*lbf) MAF METER CONNECTOR 8.5 (87, 75 in.*lbf) x3 3.0 (31, 27 in.*lbf) 9.0 (92, 80 in.*lbf) RESERVOIR BRACKET x3 IGNITION COIL CONNECTOR FUEL INJECTOR CONNECTOR NO. 2 FUEL VAPOR FEED HOSE BRAKE FLUID LEVEL SWITCH CONNECTOR BRAKE MASTER CYLINDER RESERVOIR COVER N*m (kgf*cm, ft.*lbf) : Specified torque Non-reusable part A112287E03 FU–11 1NZ-FXE FUEL – FUEL INJECTOR 9.0 (92, 80 in.*lbf) NO. 1 IGNITION COIL x4 10 (102, 7) SEAL WASHER x2 10 (102, 7) x2 x7 CYLINDER HEAD COVER SUB-ASSEMBLY FU O-RING FUEL INJECTOR ASSEMBLY NO. 1 FUEL PIPE CLAMP 19 (194, 14) VENTILATION HOSE NO. 2 VENTILATION HOSE x2 FUEL TUBE SUB-ASSEMBLY FUEL DELIVERY PIPE 9.0 (92, 80 in.*lbf) x4 INJECTOR VIBRATION INSULATOR x2 NO. 1 DELIVERY PIPE SPACER N*m (kgf*cm, ft.*lbf) : Specified torque Non-reusable part A112289E03 FU–12 1NZ-FXE FUEL – FUEL INJECTOR REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE CAUTION: • DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system. • After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray. (a) Remove the integration relay (unit C: C/OPN relay) from the engine room junction block. (b) Start the engine. After the engine has stopped, turn the power switch OFF. HINT: DTC P0171 (system too lean) may be set. (c) Check that the engine does not start. (d) Remove the fuel tank cap, and let the air out of the fuel tank. (e) Disconnect the cable from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. (f) Install the integration relay (unit C: C/OPN relay) to the engine room junction block. 2. REMOVE WINDSHIELD WIPER MOTOR AND LINK (a) Remove the windshield wiper motor and link (see page WW-13). 3. REMOVE FRONT OUTER COWL TOP PANEL SUBASSEMBLY (a) Remove the 2 bolts and disconnect the No. 2 engine room relay block. (b) Remove the 4 wire harness clamps. FU A087418E01 (c) Remove the 7 bolts and panel. 4. A087419E01 REMOVE AIR CLEANER ASSEMBLY (See page ES450) 1NZ-FXE FUEL – FUEL INJECTOR FU–13 5. REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (a) Disconnect the brake fluid level switch connector. (b) Remove the 2 bolts. (c) Disconnect the claw fitting, then remove the brake master cylinder reservoir. 6. REMOVE RESERVOIR BRACKET (a) Remove the No. 2 fuel vapor feed hose from the hose clamp. (b) Remove the connector clamp. (c) Remove the wire harness clamp. (d) Remove the 3 bolts and reservoir bracket. A087420E02 A087421E01 7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (a) Remove the 2 wire harness clamps. (b) Disconnect the 4 fuel injector connectors. (c) Disconnect the 4 ignition coil connectors. (d) Remove the 3 bolts, then remove the engine wire and brake master cylinder reservoir cover. A132572 (e) Remove the 4 bolts and 4 ignition coils. A132573 (f) Disconnect the ventilation hose from the ventilation valve. (g) Disconnect the No. 2 ventilation hose from the cylinder head cover. A087608E01 FU FU–14 1NZ-FXE FUEL – FUEL INJECTOR (h) Remove the 9 bolts, 2 seal washers, 2 nuts and cylinder head cover. FU A132574 8. No. 1 Pipe Clamp REMOVE FUEL DELIVERY PIPE (a) Disconnect the fuel tube from the fuel delivery pipe. (1) Remove the No. 1 fuel pipe clamp. Pull Out Pinch A112290E01 Nylon Tube Fuel Tube Connector O-Ring Retainer Pipe A075650E15 (2) Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel delivery pipe. NOTICE: • Remove dirt or foreign objects on the fuel tube connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them, as the fuel tube connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. 1NZ-FXE FUEL – FUEL INJECTOR FU–15 • Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tube. • If the fuel tube connector and pipe are stuck, push and pull them to release them. (b) Remove the 3 bolts and fuel delivery pipe together with the 4 fuel injectors. NOTICE: Do not drop the fuel injectors when removing the fuel delivery pipe. A087611E01 (c) Remove the 2 No. 1 delivery pipe spacers from the cylinder head. (d) Remove the 4 insulators from the cylinder head. A087612E01 9. Pull Out REMOVE FUEL INJECTOR ASSEMBLY (a) Pull out the 4 fuel injectors from the fuel delivery pipe. A088222E01 INSPECTION 1. A087468E02 INSPECT FUEL INJECTOR ASSEMBLY (a) Measure the resistance between the terminals. Standard resistance: 13.45 to 14.15 Ω at 21°C (68°F) If the resistance is not as specified, replace the fuel injector assembly. FU FU–16 1NZ-FXE FUEL – FUEL INJECTOR Fuel Tube Connector Cutter Knife Protector A112284E01 FU (b) Inspect the injection volume. CAUTION: Perform the test in a well-ventilated area away from flames. NOTICE: Carefully handle the fuel tube connector. (1) Prepare a new fuel tube. HINT: Part No. 23901-21081 (2) Using a cutter knife, cut off the protector of the fuel tube as illustrated. Tear off the protector by hand, then remove the fuel tube connector. NOTICE: If the protector is cut too deeply using the cutter, the O-ring of the fuel tube connector will be damaged. (3) Install SST to the fuel tube connector, and connect the fuel tube connector to the fuel pipe (the vehicle side). SST 09268-41047 (95336-08070) SST (Hose) Fuel Pipe Fuel Tube Connector A088228E09 SST (Hose) SST (Clamp) SST (Union) (4) Install a new O-ring to the fuel injector. (5) Install SST and the vinyl tube to the fuel injector. SST 09268-41047 (09268-41110, 0926841300) New O-Ring Vinyl Tube A088230E02 (6) Set the fuel injector to a graduated cylinder. (7) Actuate the fuel pump (see page FU-7). (8) Install SST to the fuel injector. SST 09842-30080 SST Battery Graduated Cylinder A088346E03 FU–17 1NZ-FXE FUEL – FUEL INJECTOR (9) Connect SST to the battery, then measure the injection volume for 15 seconds. Perform the inspection 2 or 3 times, then calculate the average. Standard injection volume Injection Volume Difference between each fuel injector 36 to 46 cm3 (2.1 to 2.8 cu in.) 10 cm3 (0.6 cu in.) or less NOTICE: Always turn the voltage on and off on the battery side, not the fuel injector side. If the injection volume is not as specified, replace the fuel injector assembly. (c) Inspect the leakage. (1) In the condition that the injection volume was inspected, remove SST from the battery. Inspect the fuel leakage from the fuel injector. Standard fuel drop: 1 drop or less per 12 minutes If the fuel leakage is not as specified, replace the fuel injector assembly. A088303E01 INSTALLATION 1. INSTALL FUEL INJECTOR ASSEMBLY (a) Apply a light coat of spindle oil or gasoline to a new O-ring, then install it to each fuel injector. New O-Ring A087548E02 Push Turn A088223E02 (b) Apply a light coat of spindle oil or gasoline to the surface of the fuel delivery pipe which contacts the O-ring of the fuel injector. (c) Apply a light coat of spindle oil or gasoline to the Oring again, and install the fuel injector by turning it right and left while pushing it onto the fuel delivery pipe. NOTICE: Be careful that the O-ring is not cracked or jammed when installing it. (d) Check that the fuel injector rotates smoothly. If the fuel injector does not rotate, replace the Oring. FU FU–18 1NZ-FXE FUEL – FUEL INJECTOR 2. INSTALL FUEL DELIVERY PIPE (a) Install 4 new insulators to the cylinder head. (b) Install the 2 No. 1 delivery pipe spacers to the cylinder head. NOTICE: Be careful of the installation direction of the delivery pipe spacer. A088224E01 (c) Install the fuel delivery pipe together with the 4 fuel injectors, and then temporarily tighten the 3 bolts. NOTICE: Do not drop the fuel injectors when installing the fuel delivery pipe. (d) Check that the fuel injectors rotate smoothly. If the fuel injectors do not rotate, replace the O-ring. (e) Retighten the 3 bolts to the specified torque. Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) for bolt A 9.0 N*m (92 kgf*cm, 80 in.*lbf) for bolt B B Rotate FU A A A088225E02 (f) Push Fuel Pipe Clamp A087544E04 2 1 3 A087421E02 Connect the fuel tube to the fuel delivery pipe. (1) Align the fuel tube connector with the pipe, then push in the fuel tube connector until the retainer makes a "click" sound to connect the fuel tube to the fuel delivery pipe. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the fuel tube connector and pipe before this work. • After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling them. (2) Install the No. 1 fuel pipe clamp. 3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (See page EM-39) 4. INSTALL RESERVOIR BRACKET (a) Temporarily install the reservoir bracket with the bolt labeled 1 in the illustration. (b) Tighten the 3 bolts to the specified torque in the sequence shown in the illustration. Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) (c) Install the connector clamp. (d) Install the wire harness clamp. (e) Install the No. 2 fuel vapor feed hose to the hose clamp. 1NZ-FXE FUEL – FUEL INJECTOR FU–19 5. INSTALL BRAKE MASTER CYLINDER RESERVOIR (a) Install the reservoir with the 2 bolts. Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) (b) Connect the switch connector. 6. INSTALL AIR CLEANER ASSEMBLY (See page ES453) 7. INSTALL FRONT OUTER COWL TOP PANEL SUBASSEMBLY (a) Install the panel with the 7 bolts. Torque: 6.4 N*m (65 kgf*cm, 57 in.*lbf) A087420E03 FU A087419E01 (b) Connect the 4 wire harness clamps. (c) Install the No. 2 engine room relay block with the 2 bolts. Torque: 8.4 N*m (86 kgf*cm, 74 in.*lbf) A087418E01 8. INSTALL WINDSHIELD WIPER MOTOR AND LINK (a) Install the windshield wiper motor and link (see page WW-15). 9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 10. CHECK FOR FUEL LEAKS (See page FU-8) 11. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. FU–20 1NZ-FXE FUEL – FUEL TANK FUEL TANK 1NZ-FXE FUEL ENGINE COMPONENTS INSTRUMENT PANEL FINISH PANEL LOWER CENTER CLIP FU x2 CLIP POWER OUTLET CONNECTOR GASKET FRONT FLOOR CARPET ASSEMBLY COMPRESSION SPRING FRONT EXHAUST PIPE ASSEMBLY 43 (440, 32) x2 GASKET x2 43 (440, 32) COMPRESSION SPRING N*m (kgf*cm, ft.*lbf) : Specified torque FRONT FLOOR PANEL BRACE x4 30 (302, 22) Non-reusable part A112292E03 FU–21 1NZ-FXE FUEL – FUEL TANK REAR SEAT CUSHION ASSEMBLY REAR FLOOR SERVICE HOLE COVER FUEL TANK INLET PIPE SUB-ASSEMBLY WIRE TO WIRE CONNECTOR FUEL TUBE CONNECTOR FUEL PUMP CONNECTOR FUEL FILLER PIPE CLAMP FUEL TANK ASSEMBLY NO. 1 FUEL TANK BAND SUB-ASSEMBLY RH NO. 1 FUEL TANK BAND SUB-ASSEMBLY LH x2 39 (400, 29) x2 39 (400, 29) N*m (kgf*cm, ft.*lbf) : Specified torque A112293E03 FU FU–22 1NZ-FXE FUEL – FUEL TANK FUEL TANK TO CANISTER TUBE FUEL TANK VENT HOSE CLAMP x2 FUEL SUCTION TUBE SUB-ASSEMBLY NO. 1 FUEL TUBE CLAMP NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY FU CLAMP x2 x2 6.0 (61, 53 in.*lbf) FUEL TANK WIRE TRAP CANISTER WITH PUMP MODULE FUEL TANK PRESSURE SENSOR FUEL TANK RETAINER LH FUEL TANK BREATHER TUBE GASKET TUBE JOINT CLIP CANISTER HOSE 6.0 (61, 53 in.*lbf) FUEL TANK BREATHER TUBE GASKET x2 6.0 (61, 53 in.*lbf) NO. 1 CANISTER TUBE x3 REAR FUEL TANK BRACKET NO. 1 FUEL TANK CUSHION CLAMP CANISTER x9 NO. 1 CANISTER OUTLET HOSE NUT FUEL TANK ASSEMBLY N*m (kgf*cm, ft.*lbf) : Specified torque Non-reusable part A112294E03 1NZ-FXE FUEL – FUEL TANK FU–23 REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE (See page FU-12) 2. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See page IP-18) 3. REMOVE FRONT FLOOR PANEL BRACE (See page EX-2) 4. REMOVE FRONT EXHAUST PIPE ASSEMBLY (See page EX-2) 5. REMOVE REAR SEAT CUSHION ASSEMBLY (See page SE-15) 6. REMOVE REAR FLOOR SERVICE HOLE COVER (a) Remove the butyl tape and rear floor service hole cover. (b) Disconnect the fuel pump connector. (c) Disconnect the wire to wire connector. Butyl Tape A087483E02 7. Pull Out Pinch Pinch Nylon Tube Retainer O-Ring Tank to Canister Tube Connector Pipe A112310E01 REMOVE FUEL TANK ASSEMBLY (a) Disconnect the fuel tank to canister tube. (1) Pinch the retainer of the fuel tube connector, then pull out the fuel tube connector to disconnect the fuel tank to canister tube from the pipe. NOTICE: • Remove dirt or foreign objects on the fuel tube connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tube connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank to canister tube. • If the fuel tube connector and pipe are stuck, push and pull them to release them. FU FU–24 1NZ-FXE FUEL – FUEL TANK : Pinch : Pull Out Nylon Tube O-Ring Fuel Tube Connector FU Pipe Retainer A112311E02 Push Pinch O-Ring Pipe Fuel Tank Vent Hose Connector Nylon Tube A112312E02 (b) Disconnect the No. 2 fuel tank main tube. (1) Remove the checker of the fuel tube connector from the pipe. (2) Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the No. 2 fuel tank main tube from the pipe. NOTICE: • Remove dirt or foreign objects on the fuel tube connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tube connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the No. 2 fuel tank main tube. • If the fuel tube connector and pipe are stuck, push and pull them to release them. (c) Disconnect the fuel tank vent hose. (1) Pinch the retainer and pull out the fuel tank vent hose connector with the fuel tank vent hose connector pushed to the pipe side to disconnect the fuel tank vent hose from the canister filter. NOTICE: • Remove dirt or foreign objects on the fuel tank vent hose connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank vent hose connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank vent hose. • If the fuel tank vent hose connector and pipe are stuck, push and pull them to release them. 1NZ-FXE FUEL – FUEL TANK Push Pinch Retainer Quick Connector Pipe Nylon Tube O-Ring A112313E01 Push Pinch Retainer Quick Connector Nylon Tube Pipe O-Ring A112314E01 FU–25 (d) Disconnect the fuel suction tube. (1) Pinch the retainer and pull out the suction tube connector with the suction tube connector pushed to the pipe side to disconnect the fuel suction tube from the fuel tank to filler pipe. NOTICE: • Remove dirt or foreign objects on the quick connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel suction tube connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the fuel suction tube. • If the fuel suction tube connector and pipe are stuck, push and pull them to release them. (e) Disconnect the No. 1 canister tube. (1) Pinch the retainer and pull out the No. 1 canister tube connector with the No. 1 canister tube connector pushed to the pipe side to disconnect the No. 1 canister tube from the fuel tank to filler pipe. NOTICE: • Remove dirt or foreign objects on the quick connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the No. 1 canister tube connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the tank to canister tube. • If the No. 1 canister tube connector and pipe are stuck, push and pull them to release them. FU FU–26 1NZ-FXE FUEL – FUEL TANK (f) Set a transmission jack to the fuel tank. (g) Remove the fuel filler pipe clamp and fuel tube connector from the fuel tank inlet pipe. (h) Remove the 4 bolts and No. 1 fuel tank band RH and LH. (i) Operate the transmission jack, and then disconnect the fuel tank inlet pipe. (j) Operate the transmission jack, and then remove the fuel tank. Fuel Tube Connector FU Fuel Filler Pipe Clamp A087489E02 8. A114369 REMOVE NO. 2 FUEL TANK MAIN TUBE SUBASSEMBLY (a) Remove the 3 nuts and rear fuel tank bracket. (b) Disconnect the wire to wire connector from the rear fuel tank bracket. 1NZ-FXE FUEL – FUEL TANK FU–27 (c) Disconnect the No. 2 fuel tank main tube from the clamp. (d) Remove the checker of the main tube connector from the pipe. (e) Pinch the retainer of the main tube connector, then pull out the fuel tube connector to disconnect the No. 2 fuel tank main tube from the pipe. NOTICE: • Remove dirt or foreign objects on the fuel tube connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tube connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the No. 2 fuel tank main tube. • If the fuel tube connector and pipe are stuck, push and pull them to release them. Checker Pull Out Pinch Fuel Tube Connector Nylon Tube O-Ring Pipe Retainer A112315E02 9. Pinch Push Pinch Retainer Pipe Quick Connector Nylon Tube O-Ring A112316E01 REMOVE FUEL SUCTION TUBE SUB-ASSEMBLY (a) Disconnect the fuel suction tube from the 2 No. 1 fuel tube clamps. (b) Pinch the retainer and pull out the suction tube connector with the quick connector pushed to the pipe side to disconnect the fuel suction tube from the pipe. NOTICE: • Remove dirt or foreign objects on the quick connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the suction tube connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the fuel suction tube. • If the quick connector and pipe are stuck, push and pull them to release them. FU FU–28 1NZ-FXE FUEL – FUEL TANK 10. REMOVE FUEL TANK TO CANISTER TUBE (a) Disconnect the fuel tank to canister tube from the clamp. (b) Disconnect the fuel tank to canister tube from the 2 No. 1 fuel tube clamps. (c) Remove the fuel tank to canister tube from the fuel tank. A114370 11. REMOVE TRAP CANISTER WITH PUMP MODULE (a) Disconnect the VSV connector. (b) Remove the clamp from the fuel tank vent hose and canister hose. (c) Remove the fuel tank vent hose from the 2 fuel tube clamps. (d) Remove the 2 bolts and trap canister with pump module and disconnect the ground terminal of the fuel tank wire. FU A114371 (e) Remove the gasket from the fuel tank. A087502E01 (f) A128672 Remove the 2 clamps from the trap canister with pump module. 1NZ-FXE FUEL – FUEL TANK Pinch Push Fuel Tank Vent Hose Connector Pipe Retainer O-Ring Nylon Tube A112317E01 C D B D D A FU–29 12. REMOVE FUEL TANK VENT HOSE (a) Pinch the retainer and pull out the fuel tank vent hose connector with the fuel tank vent hose connector pushed to the fuel tank vent hose side to disconnect the fuel tank vent hose from the trap with outlet valve canister. NOTICE: • Remove dirt of foreign objects on the fuel tank vent hose connector before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank vent hose connector has the O-ring that seals the pipe. • Perform this work by hand. Do not use any tools. • Do not forcibly bend, twist or turn the nylon tube. • Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank vent hose. • If the fuel tank vent hose connector and pipe are stuck, push and pull them to release them. 13. REMOVE FUEL TANK WIRE (a) Remove the clamp as shown in the illustration A. (b) Disconnect the VSV connector as shown in the illustration B. (c) Disconnect the vapor pressure sensor connector as shown in the illustration C. (d) Remove the 3 wire harness clamps as shown in the illustration D. A087496E05 14. REMOVE CANISTER (a) Disconnect the canister hose from the fuel tank retainer. (b) Disconnect the No. 1 canister outlet hose from the fuel tank. (c) Remove the bolt, 2 nuts and canister. A087497E01 FU FU–30 1NZ-FXE FUEL – FUEL TANK (d) Remove the nut from the fuel tank. A087498E01 15. REMOVE FUEL TANK PRESSURE SENSOR (a) Remove the tube joint clip, then pull out the fuel tank pressure sensor from the fuel tank retainer LH. NOTICE: • Remove dirt or foreign objects on fuel tank pressure sensor before this procedure. • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank pressure sensor has the O-ring that seals the plug. • Perform this work by hand. Do not use any tools. Pull Out FU Tube Joint Clip Fuel Tank Pressure Sensor Tube Joint Clip O-Ring A112318E05 Fuel Tank Retainer Clip Remover Gasket A087500E02 16. REMOVE FUEL TANK RETAINER LH (a) Insert a clip remover between the fuel tank retainer and gasket, then remove the fuel tank retainer by lifting it little by little. NOTICE: • The fuel tank retainer is made of resin and easily damaged if removed or installed forcibly. Handle the part correctly to ensure proper sealing. • After removing the fuel tank retainer, check that the contact surface of the fuel tank retainer on the fuel tank is not damaged. 1NZ-FXE FUEL – FUEL TANK FU–31 (b) Remove the gasket from the fuel tank. A087513E01 17. REMOVE NO. 1 FUEL TUBE CLAMP (a) Remove the 2 clamps from the fuel tank. FU A087501E01 18. REMOVE NO. 1 FUEL TANK CUSHION (a) Remove the 9 cushions from the fuel tank. A132605 INSPECTION 1. INSPECT FUEL TANK ASSEMBLY WITH FUEL PUMP (a) Measure the resistance between terminals 3 and 7. Standard resistance: 0.2 to 3.0 Ω at 20°C (68°F) If the resistance is not as specified, replace the fuel tank assembly. A087570E02 A087571E02 (b) Check that the motor operates when battery voltage is applied across the terminals. NOTICE: • Perform the check quickly (shorter than 10 seconds). • Keep the battery as far away the fuel tank as possible. • Always turn the voltage on and off on the battery side, not the fuel tank side. If the motor does not operate, replace the fuel tank assembly. FU–32 1NZ-FXE FUEL – FUEL TANK INSTALLATION 1. INSTALL NO. 1 FUEL TANK CUSHION (a) Install 9 new cushions to the fuel tank. 2. INSTALL NO. 1 FUEL TUBE CLAMP (a) Install the 2 clamps to the fuel tank. 3. INSTALL FUEL TANK RETAINER LH (a) Install a new gasket to the fuel tank. (b) While being careful that the gasket does not drop in the fuel tank, insert the fuel tank retainer LH to the fuel tank so the protrusion of the fuel tank retainer LH is in the middle of the 2 convex pats of the fuel tank. 4. INSTALL FUEL TANK PRESSURE SENSOR (a) Push the fuel tank pressure sensor to the plug of the fuel tank retainer LH, and then install the tube joint clip. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the fuel tank pressure sensor and fuel tank retainer LH before this procedure. • Check that the fuel tank pressure sensor is securely inserted to the end. • Check that the tube joint clip is on the collar of the fuel tank pressure sensor. • After installing the tube joint clip, check that the fuel tank pressure sensor cannot be pulled out. A132605 FU A087501E01 Protrusion Convex Gasket A087505E02 Push Collar Tube Joint Clip A087506E02 1NZ-FXE FUEL – FUEL TANK 5. FU–33 INSTALL CANISTER (a) Install the nut to the fuel tank. A087498E01 (b) Install the canister with the bolt and 2 nuts. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) (c) Connect the No. 1 canister outlet hose to the fuel tank. (d) Connect the canister hose to the fuel tank retainer. FU A087497E01 C D 6. INSTALL FUEL TANK WIRE (a) Install the 3 wire harness clamps as shown in the illustration D. (b) Connect the vapor pressure sensor connector as shown in the illustration C. (c) Connect the VSV connector as shown in the illustration B. (d) Install the clamp as shown in the illustration A. 7. INSTALL FUEL TANK VENT HOSE (a) Align the fuel tank vent hose connector with the pipe, then push in the fuel tank vent hose connector until the retainer makes a "click" sound to install the fuel tank vent hose to the trap canister with pump module. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the fuel tank vent hose connector and pipe before this procedure. • After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling the fuel tank vent hose connector. B D D A A087496E05 Push A114372E02 FU–34 1NZ-FXE FUEL – FUEL TANK 8. INSTALL TRAP CANISTER WITH PUMP MODULE (a) Install a new gasket to the fuel tank. (b) Insert the trap canister with pump module to the fuel tank. NOTICE: Be careful that the gasket does not drop in the fuel tank. A087504E01 (c) Install the 2 clamps to the trap canister with pump module. FU A128672 (d) Install the trap canister with pump module and connect the ground terminal of the fuel tank wire with the 2 bolts. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) (e) Install the fuel tank vent hose to the 2 fuel tube clamps. (f) Install the clamp to the fuel tank vent hose and canister hose. (g) Connect the VSV connector. A114371 9. INSTALL FUEL TANK TO CANISTER TUBE (a) Install the fuel tank to canister tube to the canister's hose. (b) Connect the fuel tank to canister tube to the 2 No. 1 fuel tube clamps. A114370 Push A114373E01 10. INSTALL FUEL SUCTION TUBE SUB-ASSEMBLY (a) Align the suction tube connector with the pipe, and then push in the suction tube connector until the retainer makes a "click" sound to install the fuel suction tube to the pipe. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the quick connector and pipe before this procedure. 1NZ-FXE FUEL – FUEL TANK FU–35 • After connecting the fuel suction tube, check that the fuel suction tube is securely connected by pulling the suction tube connector. (b) Connect the fuel suction tube to the 2 No. 1 fuel tube clamps. Checker Push A114374E01 11. INSTALL NO. 2 FUEL TANK MAIN TUBE SUBASSEMBLY (a) Align the main tube connector with the pipe, and then push in the main tube connector until the retainer makes a "click" sound to install the No. 2 fuel tank main tube to the pipe. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the fuel tube connector. • After connecting the No. 2 fuel tank main tube, check that the No. 2 fuel tank main tube is securely connected by pulling the main tube connector. (b) Install the checker to the pipe. (c) Connect the No. 2 fuel tank main tube to the clamp. (d) Connect the connector clamp to the rear fuel tank bracket. (e) Install the rear fuel tank bracket with the 3 nuts. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) A114369 12. INSTALL FUEL TANK ASSEMBLY (a) Set the fuel tank to a transmission jack. (b) Operate the transmission jack, and then install the fuel tank to the vehicle. (c) Operate the transmission jack, and then connect the fuel tank inlet pipe. FU FU–36 1NZ-FXE FUEL – FUEL TANK (d) Install the No. 1 fuel tank band RH and LH with the 4 bolts. Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf) (e) Install the fuel tube connector and fuel filler pipe clamp to the fuel tank inlet pipe. Fuel Tube Connector FU Fuel Filler Pipe Clamp A087489E02 (f) Push A087510E01 Push A087511E01 Connect the No. 1 canister tube. (1) Align the No. 1 canister tube connector with the pipe, and then push in the No. 1 canister tube connector until the retainer makes a "click" sound to connect the No. 1 canister tube to the fuel tank to filler pipe. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the No. 1 canister tube connector and pipe before this procedure. • After connecting the No. 1 canister tube, check that the No. 1 canister tube is securely connected by pulling the No. 1 canister tube connector. (g) Connect the fuel suction tube. (1) Align the suction tube connector with the pipe, and then push in the suction tube connector until the retainer makes a "click" sound to connect the fuel suction tube to the fuel tank to filler pipe. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the suction tube connector and pipe before this procedure. • After connecting the fuel suction tube, check that the fuel suction tube is securely connected by pulling the suction tube connector. 1NZ-FXE FUEL – FUEL TANK Push A087512E01 (h) Connect the fuel tank vent hose. (1) Align the fuel tank vent hose connector with the pipe, and then push in the fuel tank vent hose connector until the retainer makes a "click" sound to connect the fuel tank vent hose to the canister filter. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the fuel tank vent hose connector and pipe before this procedure. • After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling the vent hose connector. (i) Checker Push A091721E02 (j) Push A087603E02 FU–37 Connect the No. 2 fuel tank main tube. (1) Align the fuel tube connector with the pipe, and then push in the fuel tube connector until the retainer makes a "click" sound to connect the No. 2 fuel tank main tube to the pipe. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the fuel tube connector and pipe before this procedure. • After connecting the No. 2 fuel tank main tube, check that the No. 2 fuel tank main tube is securely connected by pulling the quick connector. Install the checker to the pipe. (k) Connect the fuel tank to canister tube. (1) Align the fuel tank to canister tube connector with the pipe, and then push in the fuel tank to canister tube connector until the retainer makes a "click" sound to connect the fuel tank to canister tube to the pipe. NOTICE: • Check that there are no scratches or foreign objects around the connected part of the fuel tank to canister tube connector and pipe before this procedure. • After connecting the fuel tank to canister tube, check that the fuel tank to canister tube is securely connected by pulling the quick connector. 13. INSTALL FRONT EXHAUST PIPE ASSEMBLY (See page EX-3) 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 15. CHECK FOR FUEL LEAKS (See page FU-8) 16. CHECK FOR EXHAUST GAS LEAKS FU FU–38 1NZ-FXE FUEL – FUEL TANK 17. INSTALL FRONT FLOOR PANEL BRACE (See page EX-4) 18. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See page IP-21) New Butyl Tape Convex A087515E02 FU 19. INSTALL REAR FLOOR SERVICE HOLE COVER (a) Attach new butyl tape to the rear floor service hole cover. (b) Connect the wire to wire connector. (c) Connect the fuel pump connector. (d) Install the rear floor service hole cover while adjusting it to the 3 convex parts of the floor panel. NOTICE: Be careful that the rear floor service hole cover does not overlap the convex parts of the floor panel when installing. 20. INSTALL REAR SEAT CUSHION ASSEMBLY (See page SE-23) 21. PERFORM INITIALIZATION (a) Perform initialization (see page IN-32). NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.