;bdiGDB configuration file for P4080-DS
;--------------------------------------
;
;
[INIT]
;
; Release cores for booting
;WM32    0xfe0e00e4      0x000000ff      ;BRR:
;
; setup device trigger
WDCSR   0x204           0x000000ff      ;CGCR0: Core Group 0 (0,1,2,3,4,5,6,7)
WDCSR   0x20c           0x0000000e      ;CGCR1: Core Group 1 (1,2,3)
WDCSR   0x214           0x000000f0      ;CGCR2: Core Group 2 (4,5,6,7)
;
WDCSR   0x700           0x00020001      ;CSTTACR0: trigger if a core from group 1 enter debug halt
WDCSR   0x610           0x00000022      ;CGACRD4 :if device event, halt cores in group 2
;


[TARGET]
; common parameters
POWERUP     5000                ;start delay after power-up detected in ms
JTAGCLOCK   1                   ;use 8 MHz JTAG clock (16 does not work)
WAKEUP      200                 ;give reset time to complete
;
;========================================================
; !!!! define the core ID (the #x) without any holes !!!!
; !!!! no need that core ID matches the core number  !!!!
; !!!! A valid example is: #1 CPUTYPE  P4080 5 0     !!!!
;========================================================
;
; Core#0 parameters (active vCPU after reset)
#0 CPUTYPE      P4080 0 0       ;Core0 / SOC0
#0 STARTUP      STOP 5000       ;let U-boot setup the system
#0 BREAKMODE    HARD            ;SOFT or HARD, HARD uses PPC hardware breakpoint
#0 STEPMODE     HWBP            ;ICMP or HWBP, HWBP uses a hardware breakpoint
;
;
; Core#1 parameters
#1 CPUTYPE      P4080 1 0       ;Core1 / SOC0
#1 STARTUP      RUN             ;let core run
;
; Core#2 parameters
#2 CPUTYPE      P4080 2 0       ;Core2 / SOC0
#2 STARTUP      RUN             ;let core run
;
; Core#3 parameters
#3 CPUTYPE      P4080 3 0       ;Core3 / SOC0
#3 STARTUP      RUN             ;let core run
;
; Core#4 parameters
#4 CPUTYPE      P4080 4 0       ;Core4 / SOC0
#4 STARTUP      RUN             ;let core run
;
; Core#5 parameters
#5 CPUTYPE      P4080 5 0       ;Core5 / SOC0
#5 STARTUP      RUN             ;let core run
;
; Core#6 parameters
#6 CPUTYPE      P4080 6 0       ;Core6 / SOC0
#6 STARTUP      RUN             ;let core run
;
; Core#7 parameters
#7 CPUTYPE      P4080 7 0       ;Core7 / SOC0
#7 STARTUP      RUN             ;let core run
;


[HOST]
IP              151.120.25.119
;
#0 PROMPT       P4080#0>
#1 PROMPT       P4080#1>
#2 PROMPT       P4080#2>
#3 PROMPT       P4080#3>
#4 PROMPT       P4080#4>
#5 PROMPT       P4080#5>
#6 PROMPT       P4080#6>
#7 PROMPT       P4080#7>
;

[FLASH]


[REGS]
FILE        $regP4080.def