; bdiGDB configuration file for PXA270 Board
; ------------------------------------------
;
[INIT]
WCP15   0x010F      0x00002001  ;Enable CP0 and CP13 access
;
; setup memory controller
WM32    0x48000008  0x39f2a7c3  ;MSC0
WM32    0x4800000C  0x0000a691  ;MSC1
WM32    0x48000010  0x0000b884  ;MSC2
WM32    0x48000014  0x00000001  ;MECR
;
WM32    0x48000004  0x23ca4fff  ;MDREFR : chip default
WM32    0x48000004  0x20ca201e  ;MDREFR :
WM32    0x48000004  0x20cb201e  ;MDREFR :
WM32    0x48000004  0x208b201e  ;MDREFR :
WM32    0x48000004  0x208ba01e  ;MDREFR :
WM32    0x48000000  0x00000AC8  ;MDCNFG :
DELAY   20
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0xA0000000  0xA0000000  ;access SDRAM
WM32    0x48000000  0x00000AC9  ;MDCNFG :
WM32    0x48000040  0x00000000  ;MDMRS  :
WM32    0x48000004  0x208ba01e  ;MDREFR :
;
;

[TARGET]
CPUTYPE         PXA270          ;the target CPU type
JTAGCLOCK       1               ;use 16 MHz JTAG clock
POWERUP         2000            ;start delay after power-up detected in ms
DBGHANDLER      0xFFFF0800      ;debug handler base address
;DBGHANDLER      0x00000000      ;debug handler base address
;DBGHANDLER      0x01FEF800      ;debug handler base address
;DBGHANDLER      0xFE000800      ;debug handler base address
ENDIAN          LITTLE          ;memory model (LITTLE | BIG)
BREAKMODE       SOFT            ;SOFT or HARD
;VECTOR          CATCH 0xDE      ;trap all vectors
VTABLO          0xFFFFFFFF      ;Do not update low vector table
VTABHI          0xe59ff3d8      ;Use fixed vectors "ldr pc, [pc, #3d8]"
WAKEUP          500

[HOST]
IP              151.120.25.119
FILE            E:\cygwin\home\bdidemo\xscale\vxworks
FORMAT          BIN 0xA0020000
;FILE            E:\cygwin\home\demo\xscale\fibo.x
;FORMAT          ELF
LOAD            MANUAL          ;load code code MANUAL or AUTO after reset

[FLASH]
WORKSPACE   0x5C000000          ;workspace in internal SRAM
CHIPTYPE    STRATAX16           ;Flash type
CHIPSIZE    0x1000000           ;The size of one flash chip in bytes
BUSWIDTH    32                  ;The width of the flash memory bus in bits (8 | 16 | 32)
FILE        E:\cygwin\home\bdidemo\xscale\regPXA270.def
FORMAT      BIN 0x01f00000
ERASE       0x01f00000


[REGS]
FILE	    $regPXA270.def