;bdiGDB configuration file for P4080-DS
;--------------------------------------
;
; The values used to configure the memory controller
; are the ones U-boot uses to setup my system.
; Your system may need different ones !!!
;
;
[INIT]
;
; Setup TLB1
;          MAS1       MAS2       MAS0/MAS7     MAS3
WTLB    0x80000700_0xfe00000a   0x10010000_0xfe00003f   ;1/1: fe000000->0_fe000000  16MB -I-G- RWXRWX
WTLB    0x80000900_0xe000000a   0x10020000_0xe000003f   ;1/2: e0000000->0_e0000000 256MB -I-G- RWXRWX
WTLB    0x80000a00_0x00000000   0x10030000_0x0000003f   ;1/3: 00000000->0_00000000   1GB ----- RWXRWX
WTLB    0x80000a00_0x40000000   0x10040000_0x4000003f   ;1/4: 40000000->0_40000000   1GB ----- RWXRWX
WTLB    0x80000500_0x80000000   0x10050000_0x8000003f   ;1/5: 80000000->0_80000000   1MB ----- RWXRWX
;
; Initialize LAWBAR's
WM32    0xfe000c00      0x00000000      ;LAWBAR0 : Flash @0_e0000000
WM32    0xfe000c04      0xe0000000
WM32    0xfe000c08      0x81f0001b      ;LAWAR0  : eLBC 256MB
;
WM32    0xfe000c10      0x00000000      ;LAWBAR1 : CPC1/SRAM @0_80000000
WM32    0xfe000c14      0x80000000
WM32    0xfe000c18      0x81000013      ;LAWAR1  : DDR1/CPC1 1MB
;
WM32    0xfe000df0      0x00000000      ;LAWBAR31: SDRAM @0_00000000
WM32    0xfe000df4      0x00000000
WM32    0xfe000df8      0x8100001e      ;LAWAR31 : DDR1/CPC1 2GB
;
; Use L3 cache (CPC1) as SRAM at 0x80000000
WM32    0xfe010104      0x8000000b      ;CPC1_SRCR0: all 32 ways as SRAM
WM32    0xfe010000      0x80000000      ;CPC1_CSR0 : CPC enable
WM32    0xfe010f00      0x08000000      ;CPC 4 Errata
;
; Local Bus Controller
WM32    0xfe124004      0xf8000f77      ;OR0:
WM32    0xfe124000      0xe8001001      ;BR0:
WM32    0xfe12400c      0xf8000f77      ;OR1:
WM32    0xfe124008      0xe0001001      ;BR1:
;
;
; limit memory access size
;TSZ4    0xe0000000      0xefffffff      ;flash range
;



[TARGET]
; common parameters
POWERUP     5000                ;start delay after power-up detected in ms
JTAGCLOCK   1                   ;use 16 MHz JTAG clock
WAKEUP      1000                ;give reset time to complete
CPUTYPE     P4080 0 0           ;Core0 / SOC0
EDBCR0      EDM DNH EFT         ;set run parameters
STARTUP     HALT                ;halt at the reset vector (this halts all cores !!!)
BREAKMODE   HARD                ;SOFT or HARD, HARD uses PPC hardware breakpoint
STEPMODE    HWBP                ;ICMP or HWBP, HWBP uses a hardware breakpoint
;MEMACCESS   SAP 50
;
; RCW Source Override
RCWSRC      0x18                ;Use Hard-Coded RCW 1_1000
;


[HOST]
IP          151.120.25.112
FILE        E:\temp\dump1024k.bin
FORMAT      BIN 0x10000
PROMPT      prog4080>


[FLASH]
;WORKSPACE   0x00001000          ;workspace in SDRAM
WORKSPACE   0x80001000          ;workspace in CPC1/SRAM

;flash is S29GL01GP
CHIPTYPE    MIRRORX16           ;Flash type is S29GL01GP
CHIPSIZE    0x08000000          ;The size of one flash chip in bytes
BUSWIDTH    16                  ;The width of the flash memory bus in bits
FILE        E:\temp\dump512k.bin
FORMAT      BIN 0xed800000
ERASE       0xed800000 0x20000 4


[REGS]
FILE        $regP4080.def