; Minimal bdiGDB configuration file for MPC8377E-RDB
; --------------------------------------------------
;
; The values used to configure the memory controller
; are the ones U-boot uses to setup my board.
; Your system may need different ones !!!
;
;
[INIT]
; init core register
WREG    MSR             0x00001002      ;MSR  : ME,RI
;
WM32    0xff400000      0xe0000000      ;MABR to 0xe0000000
WM32    0xe0000204      0xffff0000      ;SWCRR: disable watchdog
WM32    0xe0000110      0x00400300      ;SPCR : enable timebase unit
WM32    0xe00050d4      0x80000008      ;LCRR : CLKDIV = 8
;
; Initialize LAWBAR's
WM32    0xe0000020      0xfe000000      ;LBLAWBAR0 : Flash
WM32    0xe0000024      0x80000016      ;LBLAWAR0
WM32    0xe0000028      0x00000000      ;LBLAWBAR1
WM32    0xe000002C      0x00000000      ;LBLAWAR1
WM32    0xe0000030      0xf0000000      ;LBLAWBAR2
WM32    0xe0000034      0x80000010      ;LBLAWAR2
WM32    0xe0000038      0x00000000      ;LBLAWBAR3
WM32    0xe000003c      0x00000000      ;LBLAWAR3
;
WM32    0xe00000A0      0x00000000      ;DDRLAWBAR0 : DDR Main SODIMM
WM32    0xe00000A4      0x8000001b      ;DDRLAWAR0
WM32    0xe00000A8      0x00000000      ;DDRLAWBAR1
WM32    0xe00000AC      0x00000000      ;DDRLAWAR1
;
; Setup DDR
WM32    0xe0000128      0x80080001      ;DDRCDR
WM32    0xe0002130      0x03000000      ;DDR_CLK_CNTL
WM32    0xe0002000      0x0000000f      ;CS0_BNDS
WM32    0xe0002080      0x80010102      ;CS0_CONFIG
WM32    0xe0002104      0x00260802      ;TIMING_CFG_0
WM32    0xe0002108      0x3937d322      ;TIMING_CFG_1
WM32    0xe000210C      0x02984cc8      ;TIMING_CFG_2
WM32    0xe0002100      0x00000000      ;TIMING_CFG_3
WM32    0xe0002110      0x43000000      ;DDR_CFG
WM32    0xe0002114      0x00401000      ;DDR_CFG_2
WM32    0xe0002118      0x04400442      ;DDR_MODE
WM32    0xe000211C      0x00000000      ;DDR_MODE_2
WM32    0xe0002124      0x06090100      ;DDR_INTERVAL
DELAY   100
WM32    0xe0002110      0xc3000000      ;DDR_CFG
;
; Setup chip selects
WM32    0xe0005004      0xff800193      ;OR0 : Flash
WM32    0xe0005000      0xfe001001      ;BR0 : Flash
WM32    0xe0005014      0xfffe09ff      ;OR2 :
WM32    0xe0005010      0xf0000801      ;BR2 :
;


[TARGET]
CPUTYPE     8377                        ;the CPU type
JTAGCLOCK   1                           ;use 16 MHz JTAG clock
POWERUP     2000                        ;start delay after power-up detected in ms
WAKEUP      500                         ;give reset time to complete
STARTUP     RESET                       ;halt immediately at the boot vector
;RCW	    0xa0606c02 0x25040000	;Reset words from u-boot
;BOOTADDR    0xfff00100                 ;boot address used for start-up break
BOOTADDR    0x00000100                  ;boot address used for start-up break
BREAKMODE   HARD      	                ;SOFT or HARD, HARD uses PPC hardware breakpoint
STEPMODE    HWBP                        ;TRACE or HWBP, HWBP uses a hardware breakpoint


[HOST]
IP          151.120.25.119
FILE        E:\temp\dump512k.bin
FORMAT      BIN 0x10000
PROMPT      8377>


[FLASH]
CHIPTYPE    MIRRORX16   ;Flash type: Spansion S29GL064A R3
CHIPSIZE    0x00800000  ;The size of one flash chip in bytes
BUSWIDTH    16          ;The width of the flash memory bus in bits (8 | 16 | 32 | 64)
WORKSPACE   0x00001000  ;workspace in DDR RAM
FILE        E:\temp\dump256k.bin
FORMAT      BIN 0xfe100000
ERASE       0xfe100000 0x10000 8 ; erase 8 sectors


[REGS]
FILE        $reg8377e.def