; bdiGDB configuration file for MPC8315E-DS board
; -----------------------------------------------
;
; The values used to configure the memory controller
; are the ones U-boot uses to setup my board.
; Your system may need different ones !!!
;
[INIT]
; init core register
WREG    MSR             0x00001002      ;MSR  : ME,RI
;
WM32    0xff400000      0xe0000000      ;MABR to 0xe0000000
WM32    0xe0000204      0xffff0000      ;SWCRR: disable watchdog
WM32    0xe0000110      0x00400000      ;SPCR : enable timebase unit
WM32    0xe00050d4      0x00010002      ;LCRR : CLKDIV = 4
;
; Initialize LAWBAR's
WM32    0xe0000020      0xfe000000      ;LBLAWBAR0 : Flash
WM32    0xe0000024      0x80000017      ;LBLAWAR0
WM32    0xe0000028      0xf8000000      ;LBLAWBAR1
WM32    0xe000002C      0x8000000e      ;LBLAWAR1
WM32    0xe0000030      0xe2800000      ;LBLAWBAR2
WM32    0xe0000034      0x8000000e      ;LBLAWAR2
WM32    0xe0000038      0xfa000000      ;LBLAWBAR3
WM32    0xe000003c      0x8000000e      ;LBLAWAR3
;
WM32    0xe00000A0      0x00000000      ;DDRLAWBAR0 : DDR Main SODIMM
WM32    0xe00000A4      0x8000001a      ;DDRLAWAR0
WM32    0xe00000A8      0x00000000      ;DDRLAWBAR1
WM32    0xe00000AC      0x00000000      ;DDRLAWAR1
;
; Setup DDR
WM32    0xe0000128      0x73000002      ;DDRCDR
WM32    0xe0002130      0x02000000      ;DDR_CLK_CNTL
WM32    0xe0002000      0x00000007      ;CS0_BNDS
WM32    0xe0002080      0x80840102      ;CS0_CONFIG
WM32    0xe0002104      0x00220802      ;TIMING_CFG_0
WM32    0xe0002108      0x3935d322      ;TIMING_CFG_1
WM32    0xe000210C      0x0f9048ca      ;TIMING_CFG_2
WM32    0xe0002100      0x00000000      ;TIMING_CFG_3
WM32    0xe0002110      0x43080000      ;DDR_CFG
WM32    0xe0002114      0x00401000      ;DDR_CFG_2
WM32    0xe0002118      0x44400232      ;DDR_MODE
WM32    0xe000211C      0x8000c000      ;DDR_MODE_2
WM32    0xe0002124      0x03200064      ;DDR_INTERVAL
DELAY   100
WM32    0xe0002110      0xc3080000      ;DDR_CFG
;
; Setup chip selects
WM32    0xe0005004      0xff000193      ;OR0 : Flash
WM32    0xe0005000      0xfe001001      ;BR0 : Flash
WM32    0xe000500C      0xffff89f7      ;OR1 :
WM32    0xe0005008      0xf8000801      ;BR1 :
WM32    0xe0005014      0xffff8396      ;OR2 :
WM32    0xe0005010      0xe2800c21      ;BR2 :
WM32    0xe000501C      0xffff8ff7      ;OR3 :
WM32    0xe0005018      0xfa000801      ;BR3 :
;


[TARGET]
CPUTYPE     8315                        ;the CPU type
JTAGCLOCK   1                           ;use 16 MHz JTAG clock
POWERUP     2000                        ;start delay after power-up detected in ms
WAKEUP      500                         ;give reset time to complete
STARTUP     RESET                       ;halt immediately at the boot vector
;RCW         0xa4606c00 0x44040000       ;override reset configuration words
;BOOTADDR    0xfff00100                  ;boot address used for start-up break
BOOTADDR    0x00000100                  ;boot address used for start-up break
BREAKMODE   HARD      	                ;SOFT or HARD, HARD uses PPC hardware breakpoint
STEPMODE    HWBP                        ;TRACE or HWBP, HWBP uses a hardware breakpoint


[HOST]
IP          151.120.25.119
FILE        E:\cygwin\home\demo\mpc83xx\fibo.elf
FORMAT      ELF
;FILE        E:\temp\dump512k.bin
;FORMAT      BIN 0x10000
LOAD        MANUAL      ;load code MANUAL or AUTO after reset
PROMPT      8315>

[FLASH]
CHIPTYPE    MIRRORX16   ;Flash type:
CHIPSIZE    0x02000000  ;The size of one flash chip in bytes
BUSWIDTH    16          ;The width of the flash memory bus in bits (8 | 16 | 32 | 64)
WORKSPACE   0x00001000  ;workspace in DDR RAM
FILE        E:\temp\dump256k.bin
FORMAT      BIN 0xfec00000
ERASE       0xfec00000 0x10000 4 ; erase 4 sectors


[REGS]
FILE        $reg8315e.def