; bdiGDB configuration file for Alchemy PB1100 board
; --------------------------------------------------
;
[INIT]
;
;WCP0    12          0x00000000  ;disable interrupts
;
; Setup CPU PLL to 396 MHz
WM32    0xB1900060  0x00000021  ;CPU_PLL Configuration
; Setup Endianess
WM32    0xB1900038  0x00000001  ;Set to Little Endian
WCP0    16          0x00000003
; Setup Static Bus Controller
WM32    0xB4001000  0x00001403  ;RCS0 Configuration
WM32	0xB4001004  0x55018011	;RCS0 Timing
WM32    0xB4001008  0x11F83FE0  ;RCS0 Address

; Setup SDRAM Controller
WM32    0xB4000000  0x00000000  ;CS0 mode configuration
WM32    0xB4000004  0x00552229  ;CS1 mode configuration
WM32    0xB4000008  0x00552229  ;CS2 mode configuration
WM32    0xB400000C  0x00000000  ;CS0 address, 32MB at 0x00000000
WM32    0xB4000010  0x001003F8  ;CS1 address, 32MB at 0x02000000
WM32    0xB4000014  0x001023F8  ;CS2 address, 32MB at 0x02000000
WM32    0xB4000018  0x64000c24  ;Program refresh (disabled)
WM32    0xB400001C  0x00000000  ;Precharge all banks
WM32    0xB4000020  0x00000000  ;Issue two auto refreshes
WM32    0xB4000020  0x00000000  ;Issue two auto refreshes
WM32    0xB4000018  0x66000c24  ;Enable refresh
WM32    0xB4000024  0x00000000  ;CS0 set mode
WM32    0xB4000028  0x00000023  ;CS1 set mode
WM32    0xB400002C  0x00000023  ;CS2 set mode

[TARGET]
;CLOCK       0                     ;BDI2000: JTAG clock 16MHz
CLOCK       1                     ;BDI3000: JTAG clock 16MHz
CPUTYPE     AU1000	 ;AU1000  ;the used target CPU type
ENDIAN      LITTLE       ;BIG     ;target is little endian
STARTUP     STOP 5000             ;STOP mode is used to let the monitor init the system
RESET       JTAG		  ;the reset type (NONE, JTAG, HARD)
WORKSPACE   0xA0000000	          ;workspace in target RAM for fast download
BDIMODE     AGENT   	          ;the BDI working mode (LOADONLY | AGENT)
BREAKMODE   SOFT          	  ;SOFT or HARD, HARD uses PPC hardware breakpoints
STEPMODE    JTAG                  ;JTAG, HWBP or SWBP
VECTOR      CATCH                 ;catch unhandled exceptions

[HOST]
IP          163.181.32.78  \\THis needs to be set appropriately
FILE        BDI2000\hello.ELF
FORMAT      ELF
LOAD        MANUAL      ;load code MANUAL or AUTO after reset


[FLASH]
//THis needs to be set for the FLASH used
CHIPTYPE	MIRRORX16;
CHIPSIZE	0X800000;
BUSWIDTH	16;
FILE		yamon-02.20BOSPORUS.rec.m;The file to be loaded into FLASH
FORMAT		SREC;
WORKSPACE	0xA0100000;
ERASE		0xBFC00000;

[REGS]
DMM1	0xB4000000      ;memory controller base address
DMM2	0xB0400000      ;interrupt controller 0 base address
DMM3	0xB1800000      ;interrupt controller 1 base address
FILE	BDI2000\regau1100.def