; Configuration file for a MCF5206e board
; ---------------------------------------
;
; the initialistion list used to setup the target system
[INIT]
;       Init SIM Module
WCREG   0xC0F       0x10000001  ;MBAR: SIM registers at 0x10000000
WCREG   0xC04       0x20000001  ;SRAMBAR: Internal SRAM at 0x20000000
WM8     0x10000003  0x80        ;SIMR: enable bus monitor while freezed
WM8     0x10000041  0x04        ;SYPCR: enable bus monitor (1024 cycles)
WM8     0x100000CB  0x00        ;PAR: Pin Assignment Register PST/DDATA not needed by BDI
WM8     0x10000014  0x85        ;ICR1:
WM8     0x10000015  0x8B        ;ICR2:
WM8     0x10000016  0x8E        ;ICR3:
WM8     0x10000017  0x92        ;ICR4:
WM8     0x10000018  0x95        ;ICR5:
WM8     0x10000019  0x98        ;IRC6:
WM8     0x1000001A  0x9F        ;ICR7:
WM8     0x1000001B  0x1E        ;ICR8: SWT
WM8     0x1000001C  0x97        ;ICR9: Timer 1
WM8     0x1000001D  0x96        ;ICR10: Timer 2
WM8     0x1000001E  0x8C        ;ICR11: MBUS
WM8     0x1000001F  0x8E        ;ICR12: UART 1
WM8     0x10000020  0x8D        ;ICR13: UART 2
;       Init Chip-Select Module
WM16    0x10000064  0xFFE0      ;CSAR0: Flash at 0xFFE00000
WM32    0x10000068  0x000F0000  ;CSMR0:
WM16    0x1000006E  0x1DA3      ;CSCR0:
WM16    0x10000070  0x0000      ;CSAR1: Disable CS1
WM32    0x10000074  0x00000000  ;CSMR1:
WM16    0x1000007A  0x0000      ;CSCR1:
WM16    0x1000007C  0x0000      ;CSAR2: FSRAM at 0x00000000
WM32    0x10000080  0x000F0000  ;CSMR2:
WM16    0x10000086  0x1903      ;CSCR2:
WM16    0x10000088  0x4000      ;CSAR3: GPIO at 0x40000000
WM32    0x1000008C  0x000F0000  ;CSMR3:
WM16    0x10000092  0x0083      ;CSCR3:
;
WAREG   7           0x000ffff0  ;set initial SP
WAREG   6           0x000ffff0  ;set initial FP
;


[TARGET]
CPUTYPE     MCF5206
CPUCLOCK    54000000    ;the CPU clock rate after processing the init list
BREAKMODE   SOFT        ;SOFT or HARD
VECTOR      CATCH       ;catch unhandled exceptions

[HOST]
IP          151.120.25.119
FILE        E:\cygwin\home\demo\mcf\fibo.x
FORMAT      ELF
LOAD        MANUAL      ;load code MANUAL or AUTO after reset

[FLASH]
WORKSPACE   0x20000000  ;workspace in target RAM for fast programming algorithm
CHIPTYPE    AM29BX16    ;Flash type (AM29F | AM29BX8 | AM29BX16 | I28BX8 | I28BX16)
CHIPSIZE    0x100000    ;The size of one flash chip in bytes (e.g. AM29F010 = 0x20000)
BUSWIDTH    16          ;The width of the flash memory bus in bits (8 | 16 | 32)
FILE        D:\abatron\bdi360\ColdFire\pro\evb5206e.sss
;ERASE       0xFFE04000  ;erase sector  0 of flash
;ERASE       0xFFE06000  ;erase sector  1 of flash
;ERASE       0xFFE08000  ;erase sector  2 of flash
;ERASE       0xFFE10000  ;erase sector  3 of flash
;ERASE       0xFFE20000  ;erase sector  4 of flash
;ERASE       0xFFE30000  ;erase sector  5 of flash
ERASE       0xFFE40000  ;erase sector  6 of flash
ERASE       0xFFE50000  ;erase sector  7 of flash
ERASE       0xFFE60000  ;erase sector  8 of flash
ERASE       0xFFE70000  ;erase sector  9 of flash
ERASE       0xFFE80000  ;erase sector 10 of flash
ERASE       0xFFE90000  ;erase sector 11 of flash
ERASE       0xFFEA0000  ;erase sector 12 of flash
ERASE       0xFFEB0000  ;erase sector 13 of flash
ERASE       0xFFEC0000  ;erase sector 14 of flash
ERASE       0xFFED0000  ;erase sector 15 of flash
ERASE       0xFFEE0000  ;erase sector 16 of flash
ERASE       0xFFEF0000  ;erase sector 17 of flash


[REGS]
DMM1	0x10000000
FILE    E:\cygwin\home\bdidemo\coldfire\reg5206.def