; bdiGDB configuration for DaVinci EVM
; ------------------------------------
;
; Commands supported in the SCANINIT and SCANPOST strings:
;
;  I<n>=<...b2b1b0>   write IR, b0 is first scanned
;  D<n>=<...b2b1b0>   write DR, b0 is first scanned
;                       n  : the number of bits 1..256
;                       bx : a data byte, two hex digits
;  W<n>               wait for n (decimal) micro seconds
;  T1                 assert TRST
;  T0                 release TRST
;  R1                 assert RESET
;  R0                 release RESET
;  CH<n>              clock TCK n (decimal) times with TMS high
;  CL<n>              clock TCK n (decimal) times with TMS low
;
;
[INIT]
;
;

[TARGET]
CPUTYPE     ARM926E
;CLOCK       0 7                 ;JTAG clock : start with 1 MHz then use adaptive
CLOCK       7                   ;JTAG clock : without adaptive clocking cable
TRST        PUSHPULL            ;TRST driver type (OPENDRAIN | PUSHPULL)
RESET	    HARD	        ;NONE | HARD <n> (ms)
ENDIAN      LITTLE              ;memory model (LITTLE | BIG)
WAKEUP      100
SCANPRED    1 6                 ;count for ICEPick TAP
SCANSUCC    0 0                 ;no device after ARM926e

; Configure ICEPick module to make ARM926 TAP visible
SCANINIT    r0:w10000:
SCANINIT    r1:t1:w1000:t0:w1000:  ;assert reset and toggle TRST
SCANINIT    i6=07:d8=89:i6=02:     ;connect and select router
SCANINIT    d32=81000082:          ;set IP control
SCANINIT    d32=a018206f:          ;configure TAP0
SCANINIT    d32=a018216f:cl10:     ;enable TAP0, clock 10 times in RTI
SCANINIT    i10=ffff               ;scan bypass
;
;SCANINIT    d32=a018606f:          ;configure TAP0 for wait in reset (WIR)
;SCANINIT    d32=81000083:          ;IP control = SysReset
;SCANINIT    d32=a018616f:cl10:     ;enable TAP0, clock 5 times in RTI
;SCANINIT    i10=ffff               ;scan bypass
;
; Between SCANINIT and SCANPOST the ARM ICEBreaker is configured
; and the DBGRQ bit in the ARM debug control register is set.
;
;SCANPOST    i10=002f:              ;IP(router) - ARM(bypass)
;SCANPOST    d33=0102000106:        ;IP control = SysReset
;SCANPOST    d33=014034c2de:        ;TAP0 release from wait in reset
;SCANPOST    i10=ffff               ;scan bypass
;

[HOST]
IP          151.120.25.112
;FILE        E:\temp\large.bin
FILE        E:\temp\dump1024k.bin
FORMAT      BIN  0x00000000
LOAD        MANUAL      ;load code MANUAL or AUTO after reset
PROMPT      DaVinci>


[FLASH]
WORKSPACE   0x00001000  ;workspace in internal RAM (!!! boot mode UART !!! )
CHIPTYPE    MIRRORX16   ;Flash type is Am29LV256M
CHIPSIZE    0x02000000  ;Size is 32MB (only 16MB used, A23 fixed)
BUSWIDTH    16
FILE        E:\temp\dump16k.bin
FORMAT      BIN 0x021B0000
ERASE       0x021B0000  ;free sector


[REGS]
FILE	$reg926e.def