; bdiGDB configuration for SMDK6400 (ARM1176)
; -------------------------------------------
;
; Remove jumper J503 so TRST and RESET are not connected togehter.
; SMDK6400 drives RESET with a push-pull driver into the JTAG debug connector.
; In order to prevent driver contention, select RESET NONE.
; To reset the system, use the nRESET button, Telnet reset has no effect.
;
; The values used to configure the memory controller
; are the ones the boot ROM uses to setup my board.
; Your system may need different ones !!!
;
[INIT]
;
WM32    0x7e004000  0x00000000  ;WTCON: Watch Dog_Disable
WM32    0x7e00f120  0x00000000  ;MEM_SYS_CFG:
WM32    0x7e00f900  0x00018fde  ;OTHERS: taken from boot ROM code
WM32    0x7e00f01c  0x00000000  ;CLK_SRC: select FIN as clock source
WM32    0x7e00f000  0x0000ffff  ;APLL_LOCK:
WM32    0x7e00f004  0x0000ffff  ;MPLL_LOCK:
WM32    0x7e00f020  0x01077310  ;CLK_DIV0:
WM32    0x7e00f00c  0x81900302  ;APLL_CON:
WM32    0x7e00f010  0x81900303  ;MPLL_CON:
DELAY   100			;let PLL lock
WM32    0x7e00f01c  0x00000003  ;CLK_SRC: select PLL as clock source
CLOCK   4                       ;speed-up JTAG clock
;
WM32    0x70000000  0x00000001  ;SROM_BW:  Bank0 16-bit
WM32    0x70000004  0x00070000  ;SROM_BC0: 8 access cycles
;
WM32    0x7e001004  0x00000004  ;P1MEMCCMD: Configure
WM32    0x7e001010  0x0000030b  ;P1REFRESH:
WM32    0x7e001014  0x00000006  ;P1CASLAT:
WM32    0x7e001018  0x00000001  ;P1T_DQSS:
WM32    0x7e00101c  0x00000002  ;P1T_MRD:
WM32    0x7e001020  0x00000005  ;P1T_RAS:
WM32    0x7e001024  0x00000007  ;P1T_RC:
WM32    0x7e001028  0x00000003  ;P1T_RCD:
WM32    0x7e00102c  0x000000a8  ;P1T_RFC:
WM32    0x7e001030  0x00000003  ;P1T_RP:
WM32    0x7e001034  0x00000002  ;P1T_RRD
WM32    0x7e001038  0x00000002  ;P1T_WR
WM32    0x7e00103c  0x00000002  ;P1T_WTR
WM32    0x7e001040  0x00000002  ;P1T_XP
WM32    0x7e001044  0x0000000c  ;P1T_XSR
WM32    0x7e001048  0x0000000c  ;P1T_ESR
WM32    0x7e00100c  0x80010012  ;P1MEMCFG:
WM32    0x7e00104c  0x00000b45  ;P1MEMCFG2:
WM32    0x7e001200  0x000150f8  ;P1CHIP0CFG:
WM32    0x7e001008  0x000c0000  ;P1DIRECTCMD: Nop
WM32    0x7e001008  0x00000000  ;P1DIRECTCMD: Precharge all
WM32    0x7e001008  0x00040000  ;P1DIRECTCMD: Autorefresh
WM32    0x7e001008  0x00040000  ;P1DIRECTCMD: Autorefresh
WM32    0x7e001008  0x00080032  ;P1DIRECTCMD: MRS
WM32    0x7e001008  0x000a0000  ;P1DIRECTCMD: EMRS
WM32    0x7e001004  0x00000000  ;P1MEMCCMD: Go
;

[TARGET]
CPUTYPE     ARM1176
CLOCK       4 7                 ;JTAG clock : start with 1 MHz then use 8 MHz
POWERUP     1000                ;start delay after power-up detected in ms
WAKEUP      100                 ;wait after reset released
RESET       NONE                ;!!! SMDK6400 has push-pull driver on reset :(
                                ;!!! Press reset button on board
                                ;!!! Telnet reset has no effect
ENDIAN      LITTLE              ;memory model (LITTLE | BIG)
VECTOR      CATCH 0x001f        ;catch D_Abort, P_Abort, SWI, Undef and Reset
;VECTOR      CATCH 0x0000        ;do not catch any vector
;VECTOR      CATCH 0x0444        ;catch SMC,IRQ,SVC
BREAKMODE   SOFT                ;SOFT or HARD
;DCC         7                   ;DCC I/O via TCP port 7
;
SCANPRED    0 0                 ;no JTAG devices before the ARM1176
SCANSUCC    1 4                 ;the ETMBUF after the ARM1176 core


[HOST]
IP          151.120.25.112
FILE        E:/temp/dump1024k.bin
FORMAT      BIN 0x50000000
PROMPT      SMDK6400>


[FLASH]
; Flash is Am29LV800BB



[REGS]
FILE	$regS3C6400.def